EasyManua.ls Logo

Xantrex XHR 60-18 - Table 1.2 Electrical Specifications for 7.5 V to 40 V Models

Xantrex XHR 60-18
86 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Features and Specifications
Specifications
24 Operating Manual for XHR Series Power Supply
Table 1.2 Electrical Specifications for 7.5 V to 40 V Models
Models 7.5-130 20-50 33-33 40-25
Output Ratings:
Output Voltage
Output Current
Output Power
At the front panel binding posts:
Output Current
Output Power
0-7.5 V
0-130 A
975 W
0-30 A
225 W
0-20 V
0-50 A
1000 W
0-30 A
600 W
0-33 V
0-33 A
1089 W
0-30A
990 W
0-40 V
0-25 A
1000 W
Line Regulation:
1
Voltage (0.01% of Vmax + 2 mV)
Current (0.01% of Imax + 1 mA)
3mV
14 mA
4mV
6mA
5mV
4.3 mA
8mV
2.8 mA
Load Regulation:
2
Voltage (0.01% of Vmax + 2 mV)
Current (0.05% of Imax + 1 mA)
At the front panel binding posts:
Voltage
3mV
66 mA
650 mV
4mV
26 mA
650 mV
5mV
18 mA
650 mV
6mV
14 mA
500 mV
Meter Accuracy:
Voltage (1% of Vmax + 1 count)
Current (1% of Imax + 1 count)
0.09 V
1.4 A
0.3 V
0.6 A
0.43 V
0.43 A
0.5 V
0.35 A
Output Noise and Ripple (V):
rms
p-p (0-20 MHz)
At the front panel binding posts:
p-p (0-20 MHz)
10 mV
70 mV
250 mV
10 mV
70 mV
250 mV
7.5 mV
75 mV
350 mV
7.5 mV
75 mV
350 mV
Drift (8 hours):
3
Voltage (0.05% of Vmax)
Current (0.1% of Imax)
3.75 mV
130 mA
10 mV
50 mA
16.5 mV
33 mA
20 mV
25 mA
Temperature Coefficient:
4
Voltage (0.02% of Vmax/°C)
Current (0.03% of Imax/°C)
1.5 mV
39 mA
4mV
15 mA
6.6 mV
9.9 mA
8mV
7.5 mA
Maximum Remote Sense
Line Drop Compensation
5
3 V/line 5 V/line 5 V/line 5 V/line
OVP Adjustment Range:
(5% to 110% of Vmax) 0.375-8.25 V 1-22 V 1.65-36.3 V 2-44 V
Efficiency
6
81% 83% 83% 83%
1. For input voltage variation over the AC input voltage range, with constant rated load.
2. For 0-100% load variation, with constant nominal line voltage. Measured at the rear panel output connector unless
stated otherwise.
3. Maximum drift over 8 hours with constant line, load, and temperature, after 30-minute warm-up.
4. Change in output per °C change in ambient temperature, with constant line and load.
5. Line drop is subtracted from total voltage available at supply output.
6. Typical efficiency at 115 Vac input and rated output power.
TM-XROP-01XN.book Page 24 Monday, March 22, 2004 4:10 PM

Table of Contents

Related product manuals