03/02 How to use the Diagnostic C/E Mode
WorkCentre Pro 423/428 2-201 CHAPTER 2 TROUBLESHOOTING
Chain Function Item Description Default Description Access by
58 180 90 deg. rotation at outputting data or
report
0:Off 1:On 01 When the user can select paper on receiving data as described in
Chain=057 and Function=501, if an appropriate paper (A4SEF or
A4LEF) is not loaded, enable 90 deg. rotation (A4SEF-A4LEF) in
memory to paper that matches the size after repositioning for outputting.
This data determines whether or not to enable the 90° rotation feature.
CE
58 181 Smoothing 0:Off (Simple enlargement)
1:On
01 Main unit’s pixel density for recording is 400PPI. When the image data
received is below 400PPI, the image will be stretched to 400PPI during
process. This data determines whether or not to smooth the edge of
binary image at the stretching process.
CE
58 182 Duplex printing on Outputting (received
data print/report print/check print)
0:Off 1:On 00 Duplex printing is available with Duplex Module installed models. This
data determines whether or not to enable unconditional duplex printing
for the information of the same job when outputting data received or
reports. This feature should be handled by individual C/E and any
change will be made by each C/E. (EP-TRESS)
CE
58 183 180 deg. Rotation for Side-Two on
outputting SEF paper
0:Off 1:On 00 When “On” is selected at Chain=058 and Function=181(Duplex printing
on receiving data or reports), Main unit activates duplex recording based
on the Long Edge Binding. Therefore, when the customer wants to bind
the short edge of SEF paper, select On.
CE
58 184 180 deg. Rotation for Side-Two on
outputting LEF paper
0:Off 1:On 00 When “On” is selected at Chain=058 and Function=182(Duplex printing
on receiving data or reports), Main unit activates duplex recording based
on the Long Edge Binding. Therefore, when the customer wants to bind
the short edge of LEF paper, select On.
CE
58 301 Outputting Activity Report 0:Off 1:On 01 Determines the timing of outputting the Activity Report. When “On” is
selected, the Report will be automatically output when 50
communications of receive and send operations are accumulated.
When the Report is output manually in C/E mode, the latest 50
communication results will be output.
User
58 302 Outputting Broadcast Report 0:Off 1:On 01 While Outputting Broadcast/Multi-Poll Report as described in Chain=058
and Function=354 specifies an outputting timing for a multi-poll job, this
data specifies how to output a broadcast job.
User
58 303 Outputting Relay Broadcast Report 0:Off 1:To be sent to the specific
station
01 Specifies an outputting timing for Relay Broadcast Report. As all jobs
received from the relay broadcast station are completed, reports will be
output and send operation will be processed based on this data.
User
58 304 Outputting Send Fault (Transmission)
Report
0:Off 1:On 01 Determines whether or not to inform the operator of the specific send job
error. When “On” is selected for Transmission (Monitor) Report which
was error in communication, Send Fault (Transmission) Report will be
output regardless of the setup status.
User
58 306 Outputting Transmission report when
transmission is stopped
0:Off 1:On 00 When the operator pressed the Stop Button or stopped a send job after it
is enabled, this data determines whether or not to output Send Fault
(Transmission) Report.
User
58 310 Selecting Auto Deletion for polled
documents
00:Not to be deleted 01:To be
deleted after comm.
00 Determines how to handle the polled (confidential) documents stored in
memory
User
To Next Page
Loading...
