Need help?Do you have a question about the Yaesu SCU-LAN10 and is the answer not in the manual?
General| Brand | Yaesu |
|---|---|
| Model | SCU-LAN10 |
| Category | Control Systems |
| Language | English |
Key information and warnings for software use.
Guidelines for safe and effective remote operation.
Details on network operation limitations and phenomena.
Step-by-step guide to launching the remote control application.
Explanation of the main graphical user interface elements and layout.
How to adjust the audio output volume using the speaker icon.
Method for selecting different frequency bands.
Detailed steps for changing frequency via mouse wheel or keypad.
How to initiate and manage transmission using the PTT button.
Procedure to change the PTT button functionality to MOX.
Controls starting/stopping remote operation and error indicators.
Options for choosing different display configurations on the software screen.
Controls antenna tuner ON/OFF and initiates tuning.
Manages the VOX (Voice Operated Exchange) function.
Controls microphone gain and speech processor settings.
Controls and adjusts the monitor function for audio.
Settings for CW speed and pitch.
Controls the synchro function for frequency matching.
Manages the split frequency transmission function.
Controls transmit output power levels for different bands and modes.
Sets the monitor level for transmitted audio.
Adjusts the digital noise reduction response.
Configures the noise blanker level.
Fine-tuning VOX system parameters like gain and hang-time.
Adjusts anti-trip settings to prevent accidental transmission.
Selecting and managing memory channels for stored frequencies.
Managing memory groups and their ON/OFF status.
Selects the bandwidth of the roofing filter.
Setting shift direction for repeater operation.
Controls microphone equalizer and tone encoder/squelch functions.
Adjusts tone frequency for encoder and squelch.
Viewing and managing Quick Memory Bank entries.
Explains the 3DSS display mode and frequency tuning operations.
Details on waterfall display and frequency tuning controls.
Controls spectrum scope display modes and zeroing frequency.
Adjusts the sweep speed of the scope display using SLOW/FAST buttons.
Sets the frequency span or display range of the scope.
Switches between 3DSS and waterfall display modes.
Selects single-band or multi-display modes for the scope.
Temporarily suspends waveform drawing on the scope.
Automatically adjusts frequency to match received CW signal pitch.
Accesses scope menu for settings like band switching and markers.
Controls color density and signal/noise distinction.
Smooths waveforms and enhances display sensitivity.
Selects display colors for different SDR types.
Adjusts the size of the oscilloscope/AF-FFT display.
Configures waveform display level and time axis scale.
Adjusts the attenuator within the AF-FFT display.
Chooses which meter display is shown during transmit.
Method for changing frequency in 1MHz steps using the MHz digit.
Adjusts frequency in FAST steps using the kHz digit.
Adjusts frequency in TUNING steps using the Hz digit.
Manages memory recall and storage within the QMB.
Turns RX/TX clarifier ON/OFF and adjusts offset.
Selects the active antenna terminal.
Adjusts receive input signal attenuation levels.
Configures RF amplifier gain for signal conditions.
Selects the bandwidth of the roofing filter.
Selects AGC modes for optimum receiver recovery.
Manages memory channel recall and VFO transfer.
Imports memory data from the transceiver to the software.
Exports memory data from software to the transceiver.
Recalls memory channels and moves data to VFO.
Saves current settings to memory and removes entries.
Modifies mode, name, scan status, and display type of memory entries.
Controls receive volume and RF gain settings.
Adjusts IF filter shift frequency and bandwidth.
Turns the noise blanker ON/OFF and adjusts its level.
Activates DNR and sets its level.
Engages the digital NOTCH filter to reduce interference.
Activates the IF NOTCH filter and selects bandwidth.
Adjusts attenuation and bandwidth of the contour filter.
Enables APF for CW mode and sets bandwidth.
Manages the VC Tune function for precise tuning.
Mutes receive audio and switches transmit bands.
Controls transmission via PTT and switches to MOX mode.
Exits the remote control software.
Configures connection and audio settings for SCU-LAN10.
Sets transmit modulation and receive volumes for bands.
Configures monitor volume and auxiliary amplification settings.
Adjusts the volume for software beep notifications.
Links to user manuals and displays software details.
To Next Page
