Yamaha MDX-596 Service Manual (English)

Other manuals for Yamaha MDX-596

Questions and Answers:

M
Michael HarrisonAug 22, 2025
What to do if recording is not possible on Yamaha MDX-596 Minidisc Recorder?
- J
  John AllenAug 22, 2025
  To resolve recording issues on your Yamaha Minidisc Recorder, check the following: 1. Ensure the disc is not write-protected by sliding the write-protect tab to the closed position. 2. Verify that you are using a recordable MD, not a pre-mastered one. 3. Double-check all source connections. 4. Select the correct input jacks by pressing INPUT repeatedly. 5. Adjust the recording level using the REC LEVEL control. 6. Set the digital output level of the digital source to "MAX". 7. Use a recordable MD with available space or erase unnecessary tracks. 8. If recording was interrupted, try recording again from the beginning.
L
lisarobbinsSep 2, 2025
What to do if Yamaha Minidisc Recorder playback is not possible?
- A
  Allison SilvaSep 2, 2025
  If your Yamaha Minidisc Recorder isn't playing, first, give it 20 to 30 minutes with the power on to allow any moisture on the laser pickup to evaporate. Ensure the power is on. Check that the disc is loaded correctly, with the label side up and the arrow pointing towards the insertion slot. Make sure you're using a recorded MD, not a blank one.
B
Bradley PowersSep 1, 2025
What to do if my Yamaha Minidisc Recorder is not recording?
- R
  Raven YuSep 1, 2025
  If your Yamaha Minidisc Recorder isn't recording, ensure the disc isn't write-protected by sliding the write-protect tab to the closed position and that you're using a recordable MD, not a pre-mastered one. Verify all source connections and select the correct input jacks by pressing INPUT repeatedly. Adjust the recording level with the REC LEVEL control and ensure the digital output level of the digital source is set to “MAX”. If the MD is full, use one with fewer recorded tracks or erase unnecessary tracks. If recording was interrupted by a power issue, try recording again from the beginning.
R
Robert BartonAug 30, 2025
What to do if Yamaha MDX-596 Minidisc Recorder does not work normally?
- M
  Margaret HahnAug 30, 2025
  If your Yamaha Minidisc Recorder is malfunctioning, it might be due to strong external noise or a misoperation. Turn the power off, disconnect the AC power, wait about 30 seconds, then reconnect the power and try again.
T
Teresa StewartAug 29, 2025
Why Yamaha Minidisc Recorder remote control does not operate?
- S
  sescobarAug 29, 2025
  If your Yamaha Minidisc Recorder's remote control isn't working, try these steps: 1. Replace the batteries. 2. Ensure you're within 6 meters of the unit and within a 30° angle of the sensor. 3. Move the unit away from strong, direct light.
M
Monica WoodAug 27, 2025
What to do if playback is not possible on Yamaha Minidisc Recorder?
- T
  tpayneAug 28, 2025
  If playback is not possible on your Yamaha Minidisc Recorder, consider the following: 1. If moisture is on the laser pickup, leave the unit switched ON for 20 to 30 minutes to allow the moisture to evaporate. 2. Ensure the power is ON by pressing the POWER button. 3. Make sure the disc is loaded correctly with the label side facing up and the arrow pointing toward the disc insertion slot. 4. If "Blank Disc" appears, insert a recorded MD.
E
Erin RomanAug 26, 2025
Why does my Yamaha MDX-596 have excessive noise?
- A
  Amy DuranAug 27, 2025
  If you are experiencing excessive noise with your Yamaha Minidisc Recorder, it could be due to its proximity to other electronic devices. Try placing the unit farther away from the television or other components.
M
Miguel JoyceAug 25, 2025
How to eject MD from Yamaha MDX-596 Minidisc Recorder?
- L
  Lisa EatonAug 26, 2025
  If you can't remove the MD from your Yamaha Minidisc Recorder when it's partially inserted, it might be due to the carriage lock function being activated. Fully insert the MD, then press the EJECT button to remove it.
F
Fred TranAug 23, 2025
Why Yamaha MDX-596 Minidisc Recorder does not respond to operations?
- L
  Lisa BrownAug 23, 2025
  If your Yamaha Minidisc Recorder is not responding, the issue might be with the disc. A dirty or damaged MD can cause this. Try replacing the current disc with a new one. Also, if "UTOC ERR" appears on the display, it indicates the MD is damaged, and you should replace it.

Yamaha MDX-596 Specifications

General

Type	MiniDisc Recorder
Recording Format	MiniDisc
Sampling Frequency	44.1 kHz
Frequency Response	20 Hz - 20 kHz
Harmonic Distortion	< 0.05%
Total Harmonic Distortion	< 0.05%
Wow and Flutter	Unmeasurable
Digital Outputs	Optical
Remote Control	Yes
Power Consumption	15W
Weight	3.5 kg
Recording System	ATRAC
Signal to Noise Ratio	90 dB
Dynamic Range	90 dB
Digital Inputs	Optical, Coaxial
Analog Inputs	RCA
Analog Outputs	RCA