To Next Page
E
Elizabeth RiosSep 7, 2025
How to stop noise output from Yamaha Subwoofer?
- AAlan CannonSep 7, 2025
If a digital or high-frequency device is near the unit, try moving the Yamaha Subwoofer and the device farther apart to reduce interference.
How to stop noise output from Yamaha Subwoofer?
If a digital or high-frequency device is near the unit, try moving the Yamaha Subwoofer and the device farther apart to reduce interference.
Why won't my Yamaha MusicCast SUB 100 Subwoofer power on automatically?
If the INPUT is set to ANALOG, the unit won't operate in sync with the Pairing Master, so you'll need to turn the power on manually. Also, check your amp's settings, as a missing low-frequency input signal there could be the reason. If the unit has been without a network connection for a while, it might have entered eco standby mode, requiring you to turn it on manually.
Why is there no sound coming from my Yamaha MusicCast SUB 100?
Several factors could be at play. Ensure you're playing a source with ample low-frequency sound. Standing waves might be interfering, so experiment with the subwoofer's placement and angle. Check your amp's settings, as a missing low-frequency input signal there could be the culprit. If you're using a network connection, boost the volume via the MusicCast CONTROLLER app or the Pairing Master, or manually adjust the GAIN knob on the unit. Also, verify the network connection is correct and that the correct playback device is selected in the MusicCast CONTROLLER app or Pairing Master. For analog connections, use the GAIN knob to adjust the volume. Finally, double-check all connections to ensure they are secure and correct.
Why is network functionality not working on my Yamaha MusicCast SUB 100 Subwoofer?
If the network functionality of your Yamaha Subwoofer cannot be used, it's possible that the network information (IP address) has not been obtained correctly. To resolve this, enable the DHCP server function of your router.
How to stop noise from Yamaha MusicCast SUB 100 Subwoofer?
If the Yamaha Subwoofer is outputting noise or if an electronic device nearby is emitting noise, a digital device or a high-frequency device might be located too close to the unit. Try moving the Yamaha Subwoofer and the device farther apart.
What to do if Yamaha MusicCast SUB 100 Subwoofer power does not turn on?
If your Yamaha Subwoofer's power does not turn on, turns off immediately after being turned on, or the unit does not operate correctly, ensure that the power cord is correctly connected. Insert the power plug firmly into the AC outlet.
Why can’t I connect with the Pairing Master on my Yamaha MusicCast SUB 100 Subwoofer?
The Pairing Master might not be a MusicCast Surround/Stereo compatible device; use a compatible device or one that allows analog connections. Also, the connection might be incorrect or faulty; try initializing the unit, ensure the Pairing Master is compatible, and then connect again. If pairing with another device is already registered, cancel that pairing and redo the settings.
Why can’t I connect to the internet via the wireless LAN router (access point) with my Yamaha MusicCast SUB 100?
First, make sure your wireless LAN router is powered on. Also, the router and the unit might be too far apart; try moving them closer. Obstacles between the router and the unit can also cause connection problems, so ensure there's a clear path between them.
Why can’t I connect to the wireless LAN router (access point) with my Yamaha MusicCast SUB 100?
If MAC address filtering is enabled on your wireless LAN router, connection isn't possible. Adjust the router's settings to allow the connection.
What to do if my Yamaha MusicCast SUB 100 unit does not operate correctly?
External electric shock or a drop in power supply voltage may have caused the internal microcomputer to freeze. Disconnect the power cord from the AC outlet, wait about 30 seconds, and then plug it back in.
General| Impedance | 5 Ω |
|---|---|
| Subwoofer type | Active subwoofer |
| Subwoofer driver diameter | 20 mm |
| Subwoofer frequency range | 28 - 300 Hz |
| Subwoofer driver diameter (imperial) | 8 \ |
| On/off switch | Yes |
| Product color | White |
| Power source type | AC |
| Headphone outputs | 1 |
Weight and Dimensions| Subwoofer depth | 418 mm |
|---|---|
| Subwoofer width | 252 mm |
| Subwoofer height | 373 mm |
| Subwoofer weight | 12500 g |
Explains warning symbols for electric shock and important instructions.
Safety guidelines for power cord, electrical connections, and water exposure.
Precautions for installation, handling, fire hazards, and maintenance.
Guidelines for wireless use, medical devices, and responding to unit abnormalities.
Safety advice for power cord, installation, and avoiding environmental damage.
Warnings on hearing damage from volume and maintenance procedures.
Details on using the MusicCast CONTROLLER app for advanced device operation.
Steps to register the unit on the MusicCast network using the app.
How to link the unit with a sound bar or speaker as a Pairing Master.
Procedure to update the unit's firmware via the network.
Solutions for common problems like power not turning on or incorrect operation.
Troubleshooting steps for no sound, low-frequency issues, or unwanted noise.
Solutions for problems like inability to connect to network or internet.
Troubleshooting for app detection, connection settings, and pairing master errors.
