YASKAWA SGD7S-200A - Page 234

9.2 List of Parameters
9.2.2 List of Parameters
9-34
Pn533 2
Program Jog Operation
Movement Speed
1 to 10,000
Rotary:
1 min
-1
Direct
Drive:
0.1
min
-1
500 Rotary
Immedi-
ately
Setup
*1
Pn534 2
Program Jog Operation
Acceleration/Decelera-
tion Time
2 to 10,000 1 ms 100 All
Immedi-
ately
Setup
*1
Pn535 2
Program Jog Operation
Waiting Time
0 to 10,000 1 ms 100 All
Immedi-
ately
Setup
*1
Pn536 2
Program Jog Operation
Number of Movements
0 to 1,000 Times 1 All
Immedi-
ately
Setup
*1
Pn550 2
Analog Monitor 1 Offset
Voltage
-10,000 to
10,000
0.1 V 0 All
Immedi-
ately
Setup
*1
Pn551 2
Analog Monitor 2 Offset
Voltage
-10,000 to
10,000
0.1 V 0 All
Immedi-
ately
Setup
*1
Pn552 2
Analog Monitor 1
Magnification
-10,000 to
10,000
× 0.01 100 All
Immedi-
ately
Setup
*1
Pn553 2
Analog Monitor 2
Magnification
-10,000 to
10,000
× 0.01 100 All
Immedi-
ately
Setup
*1
Pn55A 2
Power Consumption
Monitor Unit Time
1 to 1,440 1 min 1 All
Immedi-
ately
Setup −
Pn560 2
Residual Vibration
Detection Width
1 to 3,000 0.1% 400 All
Immedi-
ately
Setup –
Pn561 2
Overshoot Detection
Level
0 to 100 1% 100 All
Immedi-
ately
Setup –
Pn580 2 Zero Clamping Level 0 to 10,000 1 mm/s 10 Linear
Immedi-
ately
Setup
*1
Pn581 2 Zero Speed Level 1 to 10,000 1 mm/s 20 Linear
Immedi-
ately
Setup
*1
Pn582 2
Speed Coincidence
Detection Signal Output
Width
0 to 100 1 mm/s 10 Linear
Immedi-
ately
Setup
*1
Pn583 2
Brake Reference Out-
put Speed Level
0 to 10,000 1 mm/s 10 Linear
Immedi-
ately
Setup
*1
Pn584 2
Speed Limit Level at
Servo ON
0 to 10,000 1 mm/s 10000 Linear
Immedi-
ately
Setup
*1
Pn585 2
Program Jog Operation
Movement Speed
1 to 10,000 1 mm/s 50 Linear
Immedi-
ately
Setup
*1
Pn586 2
Motor Running Cooling
Ratio
0 to 100
1%/
Max.
speed
0Linear
Immedi-
ately
Setup –
Pn600 2
Regenerative Resistor
Capacity
*5
Depends on
model.
*6
10 W 0 All
Immedi-
ately
Setup –
Pn601 2
Dynamic Brake Resis-
tor Allowable Energy
Consumption
0 to 65,535 10 J 0 All
After
restart
Setup
*7
Pn603 2
Regenerative Resis-
tance
0 to 65,535 10 mΩ 0All
Immedi-
ately
Setup –
Pn604 2
Dynamic Brake Resis-
tance
0 to 65,535 10 mΩ 0All
After
restart
Setup
*7
Pn621 to
Pn628
*4
–
Safety Module-Related
Parameters
–––All–––
Continued on next page.
Continued from previous page.
Parameter
No.
Size
Name
Setting
Range
Setting
Unit
Default
Setting
Applicable
Motors
When
Enabled
Classi-
fication
Refer-
ence