YASKAWA Sigma Mini SGMM Series - Page 184

4.4Servo Drive Dimensional Drawings
— 4-33 —
Incremental Encoders (Model SGMM-AjC3Jj6)
• 10 W, 20 W
UL20276
L
L1
L2
12
(0.47)
7.5
(0.30)
9.5
(0.37)
A
0.04
A
A
0.06
0.05
φ 28 (φ 1.10)
45°
j 25 (0.98)
4
16 (0.63)
6.2 (0.24)
Encoder Leads
AWG24,UL10095 or UL3266
Motor Leads
35 (1.38)
300 (11.81) ±30 (1.18)
300 (11.81)
±30 (1.18)
3 (0.12)
3 (0.12)
M3 tap screw,
depth: 4 (0.16)
18 (0.71)
(φ 0.0020)
(0.0016)
(0.0024)
3
(0.12)
2 × M3 tap screws, depth: 4 (0.16)
2xφ3.4 (φ0.13) dia.
(A)
(B)
(A): φ8
0
−0.009
(φ0.197
−0.0001
−0.0005
)
(B): φ20
0
−0.013
(φ0.79
0
−0.83
)
Shaft end
(with flat seat)
(0.16)
Type
SGMM
L mm (in) L1 mm (in) L2 mm (in) Approx.
M
Motors
yp
SGMM-
()
()
()
pp
Mass
(g)
Output W
(HP)
Torque
NSm
(lbSm)
Time
Rating
Rated
Speed
(min
−1
)
A1C3JA6 106.5
(4.19)
88.5 (3.48) 61 (2.4) 315
10 (0.013) 0.032
(0.007)
Continuous 3000
A1C3JB6
117 (4.61) 99 (3.9) 71.5 (2.81) 350
(0 00 )
A1C3JC6
()
()
()
A2C3JA6 116.5
(4.59)
98.5 (3.88) 71 (2.8) 370
20 (0.027) 0.064
(0.014)
A2C3JB6
127 (5) 109 (4.29) 81.5 (3.21) 405
(0 0 )
A2C3JC6
()
()
()
Type
SGMM
Reduction Gears
yp
SGMM-
Gear Ratio Torque
NSm (lbSm)
Rated Speed
(min
−1
)
Allowable Radial
Load N (lb)
Allowable Thrust
Load N (lb)
Lost
Motion
A1C3JA6 1/5 0.127 (0.029) 600 51.9 (11.67)
47.0 (10.57) 0.5
(d )
A1C3JB6 1/16 0.407 (0.092) 187.5 76.4 (17.19)
()
(deg)
A1C3JC6 1/25 0.636 (0.143) 120 89.2 (20.07)
A2C3JA6 1/5 0.255 (0.057) * 600 51.9 (11.67)
A2C3JB6 1/16 0.815 (0.183) 187.5 76.4 (17.19)
A2C3JC6 1/25 1.274 (0.287) 120 89.2 (20.07)
Note 1) The detector uses a 2048 P/R incremental encoder.
2) The instantaneous max. torque of the reduction gear with * is allowable max. torque of
the reduction gear. The value is not that as three times as the rated torque.
3) The keyway complies with JIS B 1301−1976 (precision). A straight key is supplied (type
with key only).
4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com