York RecipPak YEAJ44DR7 - Electrical Data (Continued); Dual Compressor Power Supply Wiring

FORM 150.60-NM4
YORK INTERNATIONAL 11
LEGEND
VOLT = Voltage
MCA = Minimum Circuit Ampacity
DISC = Disconnect
ACL = Across-the-Line
PW = Part Wind
N/A = Not Available
RLA = Running Load Amps
FLA = Full Load Amps
ACL/LRA = Across-the-Line Inrush Amps
PW/LRA = Part Wind Inrush Amps
CKT BRK = Circuit Breaker
HACR = Heating, Air Conditioning
and Refrigeration
5. Maximum HACR is based on 225% maximum plus 100% of the rated load amps for all loads
included in the circuit, per circuit, per UL 1995 Fig. 36.2.
6. The “INCOMING WIRE RANGE” is the minimum and maximum wire size that can be accommo-
dated by unit wiring lugs. The (1), (2), (3) or (4) preceeding the wire range indicates the number
of termination points available per phase of the wire range specified. The (1-2), (1-3),or (1-4)
preceeding the wire range indicates that a single multi-terminal lug is available per phase that
can accept from two (1-2) to four (1-4) wires of the wire range specified. “(1 ) #1-600MCM OR
(2) #1-250MCM” indicates that a single lug is supplied and it will accept a single wire up to
600MCM or 2 wires up to 250MCM. Actual wire size and number of wires per phase must be
determined based on ampacity and job requirements using N.E.C. wire sizing information. The
above recommendations are based on the National Electric Code and using copper connectors
only. Field wiring must also comply with local codes.
7. A ground lug is provided for each compressor system to accommodate field grounding con-
ductor per N.E.C. Article 250-54. A control circuit grounding lug is also supplied. Incoming
ground wire range is #6 - #2/0 (50 - 90 Tons) or #6 - 350 MCM (95 - 230 Tons).
DUAL COMPRESSOR POWER SUPPLY WIRING (STD) DUAL COMPRESSOR POWER SUPPLY WIRING (STD)
SYSTEM #1 WIRING SYSTEM #2 WIRING
MAX DUAL
DISC MAX SIZE
INCOMING MAX DUAL
DISC MAX SIZE
INCOMING
MCA
1
ELEM FUSE
SW MIN CKT BKR
WIRE RANGE
CPR CPR FAN
MCA
1
ELEM FUSE
SW MIN CKT BKR
WIRE RANGE
CPR CPR FAN
SIZE
4
HACR
(CU ONLY)
6
LRA
9
RLA FLA SIZE
4
HACR
(CU ONLY)
6
LRA
9
RLA FLA
MIN
2
MAX
3
A TYPE
5
MIN
2
MAX
3
A TYPE
5
279 350 450 400 700 (1-2) #4-250MCM 858 207 10.0 279 350 450 400 450 (1-2) #4-250MCM 858 207 10.0
250 300 400 250 600 (1-2) #4-250MCM 746 180 12.0 250 300 400 400 400 (1-2) #4-250MCM 746 180 12.0
147 175 250 200 350 (1-2) #4-250MCM 437 109 5.2 147 175 250 200 250 (1-2) #4-250MCM 437 109 5.2
123 150 200 200 300 (1-2) #4-250MCM 373 90 5.0 123 150 200 200 200 (1-2) #4-250MCM 373 90 5.0
135 175 225 200 300 (1-2) #4-250MCM 297 98 5.9 135 175 225 200 225 (1-2) #4-250MCM 297 98 5.9
100 125 150 200 250 (1-2) #4-250MCM 304 72 4.9 100 125 150 100 150 (1-2) #4-250MCM 304 72 4.9
146 175 250 200 350 (1-2) #4-250MCM 347 107 5.8 146 175 250 200 250 (1-2) #4-250MCM 347 107 5.8
308 400 500 400 700 (1-2) #4-250MCM 731 230 10.0 308 400 500 400 500 (1-2) #4-250MCM 731 230 10.0
275 350 450 400 600 (1-2) #4-250MCM 636 200 12.0 275 350 450 400 450 (1-2) #4-250MCM 636 200 12.0
162 200 250 200 400 (1-2) #4-250MCM 385 121 5.2 162 200 250 200 250 (1-2) #4-250MCM 385 121 5.2
136 175 225 200 300 (1-2) #4-250MCM 318 100 5.0 136 175 225 200 225 (1-2) #4-250MCM 318 100 5.0
165 200 250 200 400 (1-2) #4-250MCM 410 122 5.9 165 200 250 200 250 (1-2) #4-250MCM 410 122 5.9
110 150 175 200 250 (1-2) #4-250MCM 254 80 4.9 110 150 175 200 175 (1-2) #4-250MCM 254 80 4.9
180 225 300 200 450 (1-2) #4-250MCM 412 134 5.8 180 225 300 200 300 (1-2) #4-250MCM 412 134 5.8
308 400 500 400 700 (1-2) #4-250MCM 731 230 10.0 308 400 500 400 500 (1-2) #4-250MCM 731 230 10.0
275 350 450 400 600 (1-2) #4-250MCM 636 200 12.0 275 350 450 400 450 (1-2) #4-250MCM 636 200 12.0
162 200 250 200 400 (1-2) #4-250MCM 385 121 5.2 162 200 250 200 250 (1-2) #4-250MCM 385 121 5.2
136 175 225 200 300 (1-2) #4-250MCM 318 100 5.0 136 175 225 200 225 (1-2) #4-250MCM 318 100 5.0
165 200 250 200 400 (1-2) #4-250MCM 410 122 5.9 165 200 250 200 250 (1-2) #4-250MCM 410 122 5.9
110 150 175 200 250 (1-2) #4-250MCM 254 80 4.9 110 150 175 200 175 (1-2) #4-250MCM 254 80 4.9
180 225 300 200 450 (1-2) #4-250MCM 412 134 5.8 180 225 300 200 300 (1-2) #4-250MCM 412 134 5.8
353 450 600 400 800 (1-2) #1/0-500MCM 950 266 10.0 308 400 500 400 500 (1-2) #4-250MCM 731 230 10.0
313 400 500 400 700 (1-2) #4-250MCM 826 231 12.0 275 350 450 400 450 (1-2) #4-250MCM 636 200 12.0
186 225 300 200 450 (1-2) #4-250MCM 467 140 5.2 162 200 250 200 250 (1-2) #4-250MCM 385 121 5.2
156 200 250 200 350 (1-2) #4-250MCM 413 116 5.0 136 175 225 200 225 (1-2) #4-250MCM 318 100 5.0
170 200 250 200 400 (1-2) #4-250MCM 482 126 5.9 165 200 250 200 250 (1-2) #4-250MCM 410 122 5.9
125 150 200 200 300 (1-2) #4-250MCM 330 92 4.9 110 150 175 200 175 (1-2) #4-250MCM 254 80 4.9
186 225 300 200 450 (1-2) #4-250MCM 572 139 5.8 180 225 300 200 300 (1-2) #4-250MCM 412 134 5.8
365 450 600 400 800 (1-2) #1/0-500MCM 950 266 16.0 365 450 600 400 600 (1-2) #1/0-500MCM 950 266 16.0
322 400 500 400 800 (1-2) #4-250MCM 826 231 16.4 322 400 500 400 500 (1-2) #4-250MCM 862 231 16.4
192 250 300 200 450 (1-2) #4-250MCM 467 140 8.2 192 250 300 200 300 (1-2) #4-250MCM 467 140 8.2
162 200 250 200 400 (1-2) #4-250MCM 413 116 8.1 162 200 250 200 250 (1-2) #4-250MCM 413 116 8.1
177 225 300 200 400 (1-2) #4-250MCM 482 126 9.7 177 225 250 200 300 (1-2) #4-250MCM 482 126 9.7
127 150 200 200 300 (1-2) #4-250MCM 330 92 5.9 127 150 200 200 200 (1-2) #4-250MCM 330 92 5.9
193 250 300 200 450 (1-2) #4-250MCM 572 139 9.2 193 250 300 200 300 (1-2) #4-250MCM 572 139 9.2
424 500 700 600 1000 (1-2) #1/0-500MCM 1101 313 16.0 365 450 600 400 600 (1-2) #1/0-500MCM 950 266 16.0
373 450 600 400 800 (1-2) #4-250MCM 976 272 16.4 322 400 500 400 500 (1-2) #4-250MCM 826 231 16.4
223 300 350 250 500 (1-2) #4-250MCM 591 165 8.2 192 250 300 200 300 (1-2) #4-250MCM 467 140 8.2
187 225 300 200 450 (1-2) #4-250MCM 488 136 8.1 162 200 250 200 250 (1-2) #4-250MCM 413 116 8.1
234 300 400 250 500 (1-2) #4-250MCM 585 171 9.7 177 225 300 200 300 (1-2) #4-250MCM 482 126 9.7
149 175 250 200 350 (1-2) #4-250MCM 390 109 5.9 127 150 200 200 200 (1-2) #4-250MCM 330 92 5.9
254 300 400 250 500 (1-2) #4-250MCM 668 188 9.2 193 250 300 200 300 (1-2) #4-250MCM 572 139 9.2
424 500 700 600 1000 (1-2) #1/0-500MCM 1101 313 16.0 424 500 700 400 700 (1-2) #1/0-500MCM 1101 313 16.0
373 450 600 400 800 (1-2) #4-250MCM 976 272 16.4 373 450 600 400 600 (1-2) #1/0-500MCM 976 272 16.4
223 300 350 250 500 (1-2) #4-250MCM 591 165 8.2 223 300 350 400 350 (1-2) #4-250MCM 591 165 8.2
187 225 300 200 450 (1-2) #4-250MCM 488 136 8.1 187 225 300 200 300 (1-2) #4-250MCM 488 136 8.1
234 300 400 250 500 (1-2) #4-250MCM 585 171 9.7 234 300 400 400 400 (1-2) #4-250MCM 585 171 9.7
149 175 250 200 350 (1-2) #4-250MCM 390 109 5.9 149 175 250 200 250 (1-2) #4-250MCM 390 109 5.9
254 300 400 250 600 (1-2) #4-250MCM 668 188 9.2 254 300 400 400 400 (1-2) #4-250MCM 668 188 9.2