YORK INTERNATIONAL
94
OPTIONAL DECORATIVE TAMPERPROOF
ENCLOSURE (LOUVERED & WIRE GRILLE)
General
A louvered tamperproof enclosure is available for chiller
for the prime purpose of deterring unauthorized access
to components of the chiller.
Kits 475-04262-002 is the decorative/tamperproof en-
closure which consists of louvered sheet metal panels
along with mounting hardware. This kit has a further
purpose of presenting a pleasing appearance to the
chiller when it is located in a highly visible area. Two
kits must be installed to complete the installation.
Installation
1. Refer to Fig. 46 and the associated parts list. Before
starting installation, all of the items should be identi-
fied by comparing with Fig. 47.
2. All holes for mounting kit parts are provided in both
the chiller frame and the added supports; therefore,
it should be unnecessary to drill holes.
3. Install the louvered panels using the proper hardware
and supports. Refer to Fig. 47 and the Parts List for
placement of the panels and the proper hardware
required. Discard existing grilles to attach the lou-
vered panels where necessary.
4. Notch grilles to suit water connection and wiring har-
nesses as needed.
5. If the High Ambient Sunshield Kit or Disconnect Op-
tion is installed, field adaption will be required where
parts of the kits interfere. Touch up exposed metal
parts to prevent rust.
FIG. 47 LOUVER INSTALLATION FOR EACH KIT
PART # ITEM QTY DESCRIPTION
075-02563-001 1 6 PANEL, LOUVERS SIDE BTM.
075-02563-002 2 8 PANEL, LOUVERS SIDE TOP
075-02563-016 3 1 PANEL, LOUVERS Front Top L.H.
075-02563-015 4 1 PANEL, LOUVERS Front Top R.H.
075-02563-005 5 2 PANEL, LOUVERS REAR TOP
075-02563-006 6 2 PANEL, LOUVERS REAR BTM.
075-02563-018 7 1 SUPPORT, FRONT CTR.
075-02563-021 8 1 SUPPORT, FRONT R.H.
075-02563-019 9 1 PANEL, Louvers Front BTM. R.H.
075-02563-020 10 1 PANEL, Louvers Front BTM. L.H.
075-02563-014 11 1 PANEL, Louvers Side BTM. L.H. FR.
075-02563-013 12 1 PANEL, Louvers Side BTM. L.H. RR.
075-02501-000 13 12 BRACKET
075-02502-000 14 22 CLIP, RETAINER
075-02503-000 15 4 CLIP, RETAINER
075-04287-000 16 2 CLIP, TIE
075-02563-022 17 1 SUPPORT, FRONT L.H.
075-02563-023 18 1 SUPPORT, TOP L.H.
075-02563-024 19 1 SUPPORT, TOP R.H.
075-02563-017 20 1 PANEL, LOUVERS FRONT TOP
021-16205-000 51 52 SCREW, CAP HEX 3/8-16 x 1-1/2
021-16158-000 52 52 LKWASHER SPG. 3/8
021-16139-000 53 52 NUT, HEX 3/8
021-16136-000 54 213 SCREW, TAP CUT 1/4 x 1/2
021-16161-000 55 15 SCREW, CAP HEX 1/4-20 x 3/4
021-16210-000 56 15 LKWASHER SPG. 1/4
021-16151-000 57 15 NUT, HEX 1/4
021-17223-000 58 2 SCREW, CAP HEX 1/2-13 x 1
021-16157-000 59 2 LKWASHER SPG. 1/2
021-16155-000 60 2 NUT, HEX 1/2
021-17055-000 62 10 SCREW, CAP HEX 1/4-20 x 1/2
021-16999-000 63 10 NUT, HEX 1/4
021-01248-000 64 10 WASHER, PLAIN 5/16 ID
021-01148-000 65 10 LKWASHER 1.4
Parts List For Each Kit
LD01955
FIG. 46 COMPLETED INSTALLATION
00028TG
To Next Page
Loading...
