Need help?Do you have a question about the Zanotti MSB3370Y2 Series and is the answer not in the manual?
General| Brand | Zanotti |
|---|---|
| Model | MSB3370Y2 Series |
| Category | Cooling boxes |
| Language | English |
Unit is not suitable for explosive environments; use in such atmosphere is forbidden.
Coldroom must have min. 4 m³ free volume; ambient requires min. 20 m³ ventilation.
Unit not suitable for salty environments; protect condenser and evaporator.
Do not discharge refrigerant; it must be recovered by specialized technicians.
Comply with EU legislation (PED, ATEX, EN378) for locating and operating the unit.
Avoid damaging pipes, prevent fire risk from refrigerant exposure, use specialized technicians and equipment.
Unit consists of condensing unit, evaporator, electric connection box, and remote control panel.
Compression units produce cold by vaporizing refrigerant (R290) in an evaporator.
Handle unit by lifting and transport means, ensuring safety of personnel.
Table providing dimensions for various SB unit models.
Place unit in well-ventilated room, limit door openings, ensure good air supply/discharge.
Leave enough free room for opening, use, and maintenance in safe conditions.
Fix back plate vertically, connect cable without bundling it with others.
Lists mechanical (protections) and electrical (fan protection, pressure switches) safety devices.
Clean unit carefully, remove dust and dirt. Solvents are not allowed.
Check voltage/frequency, use safety device (circuit breaker/RCD), connect according to wire colours.
Unit has a cable for cold room lamp connection (230V, 100W max).
Do not connect microdoor, light, or heater cables to the 230V line; each has a specific plate.
Any defective electrical part must be replaced exclusively by trained personnel.
Connect water inlet/outlet pipes as indicated; min. 1 bar water pressure required.
Refers to the annexed manual controller.
Check locking screws, electrical connections, ensure no tools left, correct assembly, no gas leaks, front cover secured.
Connect to mains, check display (OFF), perform preheating/voltage monitor phases, press ON/OFF, set temperature.
Connect to mains, press ON/OFF, press SET, use UP/DOWN keys to adjust temperature.
Steps for installing air flow conveyor and fixing components.
Connect door cable to X4, noting cable type and correct plug orientation.
Connect the remote panel to X5 using the appropriate cable.
Connect water outlet, water inlet, and condensate evacuation pipes.
Set addresses 1 to N for master/slave units via the remote panel.
Connect X7 of master to X8 of 1st slave, and subsequent slaves similarly.
Control units via "ALL" (all units), "LOC" (local unit), or specific address.
Refers to an enclosed wiring diagram specific to SB series units.
Keep room venting on, inspect pipe lines, handle R290 safely, purge with nitrogen, use appropriate caps.
Periodically clean the condenser by blowing air from inside outwards.
Use safety gloves and always disconnect unit before working.
Periodically check wear condition of electrical contacts and remote switches.
User cannot replace electrical parts, work on electrics, repair mechanical parts, or work on the refrigeration system.
User cannot work on the control panel, ON/OFF/emergency switches, or safety devices.
Compressor may stop due to overheating, poor ventilation, voltage anomaly, or fan fault.
Ice may form due to frequent door opening, fan fault, or defrost issues.
Check power, mains cable connection, and internal fuses if the display does not light up.
Check microdoor connection if the unit does not start after pressing ON/OFF.
Refers to the manual of the electronic controller for alarm details.
Refer to the unit plate number when ordering spare parts.
Check door seals, cold dispersion, proper room use, and evaporator for ice.
Do not use hot water/metal objects for ice removal; do not remove protections during operation.
Dispose of wooden, plastic, polystyrene packing according to country regulations.
Dispose of scrapped components via specialized waste collection companies.
Do not discharge refrigerant into the atmosphere; dispose of via specialized collection services.
Details parameters like Differential, Set Points, Delays, Defrost settings, and Alarm configurations.
Details parameters related to alarm settings, input/output configurations, and energy saving.
Details parameters related to P1/P2 configuration, calibration, LAN settings, and browsing functions.
Explains 'CA', 'PrP' flashing indicators for pressure switch activations.
Lists designations for sensors, heaters, and other components.
Lists designations for fuses, components, alarms, and lights.
Lists designations for compressors, motors, and contactors.
Lists designations for switches, transformers, and terminal boards.
To Next Page
