Zebra reserves the right to make changes to any product to
improve reliability, function, or design. Zebra does not assume any
product liability arising out of, or in connection with, the application
or use of any product, circuit, or application described herein. No
license is granted, either expressly or by implication, estoppel, or
otherwise under any patent right or patent, covering or relating to
any combination, system, apparatus, machine, material, method,
or process in which Zebra products might be used. An implied
license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Zebra Technologies Corporation Lincolnshire, IL USA
http://www.zebra.com
© 2018 ZIH Corp and/or its affiliates. All rights reserved. ZEBRA
and the stylized Zebra head are trademarks of ZIH Corp,
registered in many jurisdictions worldwide. All other trademarks
are the property of their respective owners.
MN-002762-06 Revision A — April 2018
Rugged Bluetooth
Headset
HS3100
Quick Start Guide
Features
Over-the-Head (OTH)
Behind-the-Neck (BTN)
LED Indicator
Charge the Battery
Insert the battery into the charger with the contacts facing forward.
Insert the Battery
Insert the battery with the contacts facing outward.
Power On Headset
Press the Main Function button to turn the power on. The headset
LED illuminates blue and flashes three times.
Pair Headset with Device
The headset can be paired with other Bluetooth devices in the
following ways:
•
Touch-to-pair with devices supporting an NFC connection
•
Standard Bluetooth pairing where the host receives the headset
information via an offline mechanism and connects with it
•
Standard Bluetooth pairing where the headset is discovered by
the host.
Position the Boom
Do not rotate the boom beyond the stop point.
* Applies to OTH model. The BTN model has only left side boom
placement.
Adjust the OTH Headband
The headband can be squeezed for a tighter fit to the head and
clicks as it is positioned into place. When adjusting the headband,
•
Position the ear pad in the center of the ear.
•
Position the T-Bar above the ear, half way between the top of
the ear and the top of the head.
Adjust the Microphone
Position the microphone icon so that it is facing your mouth.
Adjust the Microphone Boom
Place the microphone two finger’s width away from the corner of
your mouth, so it is slightly to one side.
Mute the Microphone
Place the microphone boom in the upright position.
Adjust the Volume
Audio Tones
Maintenance
Replace T-Bar
* Applies to OTH model.
Replace Headband
Disassemble the headset to replace the headband.
Replace Ear Pad
Firmly grip and pull the ear pad and inner casing.
Align and snap the new ear pad into position.
Replace Windscreen
Remove the Battery
More Information
For more information, refer to the HS3100 Rugged Bluetooth
Headset User Guide.
NOTE This guide applies to both the OTH and BTN
headband models, unless otherwise noted.
LED Indicator
(with no charger plugged in)
Headset Status
Three Blue Flashes Power On
Three Red Flashes Power Off
Blue and Red Alternate Flashes Pairing Mode
Slow Blue Flash Connected
Steady Blue Not Connected
Slow Two Red Flashes Low Battery
Adjustable Headband
Microphone with Windscreen
Flexible Microphone Boom
T-Bar
Foam Ear Pad
Battery
Disassembly Knob
Multi-
Function
Button with
LED Indicator
Volume Buttons
NFC Tag
Left Placement
Foam Ear Pad
Headband
Microphone with Windscreen
Flexible Microphone Boom
Disassembly Knob
Battery
Volume Buttons
Multi-Function
Button with
LED Indicator
NFC Tag
Condition Action Headset State
Headset in Low Power
Mode
Press Multi-Function Button
for two seconds
Headset goes into Pairing
Mode or in Connected state
Headset in Low Power
Mode
Press Multi-Function Button
for three seconds
Headset goes into Pairing
Mode
Headset is ON or
Connected
Press Multi-Function Button
for two seconds
Headset goes into Low
Power Mode
Left Side Boom
Placement
Right Side Boom
Placement
Function Audio Tones
Start Pairing Two short low tones
Successful Pairing Three rising tones
Headset Connected One tone
Link Lost Two low tones followed by a high tone
Low Battery Two short tones every two minutes until shutdown
Mute Two descending tones
Un-mute Two rising tones
Power Up Four tones
Power Down Four descending tones
To Next Page
Need help?
General
Weight and Dimensions
