Zebra S4M - Page 34

S4M
Specifications Subject to Change without Notice Technical Specifications
Product Guide 34 November 2005
• Vertical = < ±0.039" (±1.0mm) on non-continuous media
Horizontal = <
±0.039" (±1.0mm) within a roll of media
• Programmable print speeds:
- 203 dpi models = 2.0" (51mm) through 6" (152 mm) per
second in 1" increments
- 300 dpi model = 2.0" (51mm) through 6" (152mm) per
second in 1" increments
Media Specifications
• Maximum non-continuous label length: 39" (991mm)
• Media type: continuous, die-cut, tags, black-mark
• Media web width (label and liner):
0.75" (19.4mm) to 4.50" (114mm)
• Minimum label length:
- Tear-off mode: 0.7" (17.8mm)
- Peel mode: 0.5" (12.7mm)
• Media thickness (label and liner):
0.003" (0.076mm) to 0.010" (0.25mm)
• Maximum media roll size:
8.0" (203mm) O.D. on a 3" (76mm) I.D. core
6.0” (152mm) O.D. on a 1” (25mm) I.D. core
• Maximum fan-fold pack size:
8.0"L (203mm) x 4.5"W (114mm) x 6.2"H (157mm)
• Gap and notch sensing standards:
- Inter-label gap: 2 - 4mm, preferably 3mm
- Sensing notch: 0.25"W (6mm) x 0.12"L (3mm)
- Sensing hole: 0.125" (3mm) diameter
* Note:
Notch & Hole Position centered from 0.15” to
2.25” from media inner edge
• Fixed transmissive sensor location: 7/16” from media inner
edge
• Black mark sensing standards:
- Black mark length (parallel to inside media edge):
0.098" - 0.453" (2.5mm - 11.5mm)
- Black mark width (perpendicular to inside media edge):
> 0.37" (> 9.5mm)
- Black mark location: within 0.040" (1mm) of inside media
edge
- Black mark density: > 1.0 Optical Density Units (ODU)
- Maximum media density: 0.5 ODU
Ribbon Specifications (Thermal Transfer
Option Only)
• Ribbon width: 1.57" (40mm) to 4.33" (110mm)
• Standard Lengths: 984' (300m) or 1476' (450m)
• Maximum ribbon roll size:
3.2" (81.3mm) O.D. on a 1.0" (25.4mm) I.D. core
• Ribbon wound ink-side out
Standard Printer Fonts (ZPL firmware Only)
Fonts A, B, C, D, E, F, G, H, and GS are expandable up to 10 times,
height and width independently. However, fonts E and H (OCR-A
and OCR-B) are not considered “in-spec" when expanded.
The scalable smooth font 0 (CG Triumvirate™ Bold Condensed) is
expandable on a dot-by-dot basis, height and width independent,
while maintaining smooth edges. Maximum character size depends
on available memory.
IBM Code Page 850 international character sets are available in the
fonts A, B, C, D, E, F, G, and 0 through software control.
Font Matrix Type
*
Character Size
Inches Millimeters
Height Width Inter-character Gap Height Width Char/inch Height Width Char/inch
A 9 5 1 U-L-D 0.044 0.029 33.90 1.13 0.75 1.33
B 11 7 2 U 0.054 0.044 22.60 1.38 1.13 0.89
C,D 18 10 2 U-L-D 0.088 0.059 16.95 2.25 1.50 0.67
E 28 15 5 OCR-B 0.138 0.098 10.17 3.50 2.50 0.40
F 26 13 3 U-L-D 0.128 0.079 12.71 3.25 2.00 0.50
G 60 40 8 U-L-D 0.295 0.236 4.24 7.50 6.00 0.17
H 21 13 6 OCR-A 0.103 0.093 10.71 2.63 2.38 0.42
GS 24 24 0 SYMBOL 0.118 0.118 8.48 3.00 3.00 0.33
P 20 18 N/A U-L-D .098 .089 N/A 2.49 2.26 N/A
Q 28 24 N/A U-L-D .138 .118 N/A 3.51 2.99 N/A
R 35 31 N/A U-L-D .172 .153 N/A 4.37 3.89 N/A
S 40 35 N/A U-L-D .197 .172 N/A 5.00 4.37 N/A
T 48 42 N/A U-L-D .236 .207 N/A 5.99 5.26 N/A
U 59 53 N/A U-L-D .290 .261 N/A 7.37 6.63 N/A
V 80 71 N/A U-L-D .394 .349 N/A 10.0 8.86 N/A
0 Default: 15 x 12 U-L-D Scalable
*U = Uppercase, L = Lowercase, D = Descenders
Font Matrices for 8 dot/mm (203 DPI) Print heads
Font Matrix Type* Character Size
Inches Millimeters
Height Width Inter-character Gap Height Width Char/inch Height Width Char/inch
A 9 5 1 U-L-D .030 0.020 50.00 0.76 0.51 1.97
B 11 7 2 U .037 0.030 33.33 0.93 0.76 1.31
C,D 18 10 2 U-L-D .060 0.040 25.00 1.53 1.02 0.98
E 41 20 6 OCR-B .137 0.087 11.54 3.47 2.20 0.45
F 26 13 3 U-L-D .087 0.053 18.75 2.20 1.36 0.74
G 60 40 8 U-L-D .200 0.160 6.25 5.08 4.07 0.25
H 30 19 9 OCR-A .100 0.093 10.71 2.54 2.37 0.42
GS 24 24 0
SYMBOL
.080 0.080 12.50 2.03 2.03 0.49
P 20 18 N/A U-L-D .098 .089 N/A 2.49 2.26 N/A
Q 28 24 N/A U-L-D .138 .118 N/A 3.51 2.99 N/A
R 35 31 N/A U-L-D .172 .153 N/A 4.37 3.89 N/A
S 40 35 N/A U-L-D .197 .172 N/A 5.00 4.37 N/A
T 48 42 N/A U-L-D .236 .207 N/A 5.99 5.26 N/A
U 59 53 N/A U-L-D .290 .261 N/A 7.37 6.63 N/A
V 80 71 N/A U-L-D .394 .349 N/A 10.0 8.86 N/A
0 Default: 15 x 12 U-L-D Scalable
*U = Uppercase, L = Lowercase, D = Descenders
Font Matrices for 12 dot/mm (300 DPI) Print heads