Zelmer 17Z021 - Technical Data; Kettle Structure and Preparation; Structure of the Kettle; Preparation for Operation

35
GW17-053_v02
Technical data
The technical parameters are given on the data plate of the
product.
1.7 liter capacity.
Zelmer electric kettles are built in I class insulation and they
are equipped with supplying cord with grounding wire and
grounding plug.
The ZELMER kettle meets the requirements of the standards
in force.
The appliance is compliant with the requirements of the
following directives:
The Low Voltage Directive (LVD) – 2006/95/EC. –
Electromagnetic Compatibility (EMC) – 2004/108/EC. –
The product is afxed with a CE Mark on the data plate.
Structure of the kettle (Fig. A)
1
Metal casing
2
Water level indicator
3
Spout
4
Lid
5
Lid release button
6
Handle
7
On/off button
8
Storage space for the connecting cord
9
Supplying cord
10
Antideposit lter
11
Base
Preparation of the electric kettle for
operation
 Before the rst use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”),llitwithwateruptothe“max”
level,andletitboilfourtimes(usefreshwater
eachtime)andwashagain.
Operating instructions of the electric kettle
(Fig. B)
1
Press the lid button (5) – the kettle lid will open.
2
Place the lter (10) in the kettle – if it was taken out
before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator (2)).
 Donotboilthewaterifitisbelowtheminimum
level or beyond the maximum level on the
indicator(2).
4
Close the lid.
5
Place the kettle on the power base (11).
6
Put the plug of the connecting cord into a mains socket
with an earth pin – the upper part of the kettle body will
light up.
7
Turn the kettle on by pressing the lever (7) – the indicator
light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
 Becarefulnottollupwithwaterbeyondthe
nominalcapacitywhenpouringwaterintothe
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the lter
slowing down the speed of the ow. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched on, it will be
switched off by a thermal device automatically.
In order to switch the kettle on again after it has cooled down
(approx. 15 minutes), take it off the base, replace it and
switch the kettle on by pressing the lever (7). The cooling
down of the kettle can be accelerated by puring cold water
into the kettle.
Cleaning and maintenance (Fig. C)
Alwayscleanacoldkettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Take out the lter (10).
3
Clean the outside surfaces with a soft cloth moistened
with washingup liquid.
In order to remove the buildup of hard water lm from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Filter replacement – descaling
In the event that scale builds up on the bottom of the kettle,
it needs to be removed. 6% or 10% vinegar is used for this
purpose.
Open the lid
●
(5).
Take out the lter
●
(10).
Wash the lter under running water.
●
Pour in 0.5 l of vinegar and switch on the kettle
●
(7).
Boil the vinegar and leave in the kettle for about 30
●
minutes.
Pour the vinegar out and rinse the kettle with fresh
●
water.