ZeroWater 6 - Page 2

20879-01A/20627 READY READ: 13nal_ZW_RR_Pamphlet_ENG FRENCH 52 cup.ai | smithdesign.com
05.09.23 | ZEROWATER | ZeroWater Cooler Jug Pamphlet | Revision 13nal
AM: JG | AD: MH | DES: tt
13nal
SPREAD 2
ENGLISH - 52cup
1 2
ASSEMBLE YOUR ZEROWATER
PITCHER QUICKLY AND EASILY
STEP 1
Remove the TDS meter from packaging and test your
tap water. Compare to TDS chart on page 3 to help
give a gauge of filter life.
*For Ready-Read products detach integrated meter
from device.
STEP 2
Remove lid and reservoir from device. Unwrap filter and
remove branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using mild soap
then rise and dry thoroughly. Then rinse the exterior
of your filter with warm water for 30 seconds.
*Reminder please rewash your device with each
filter change.
STEP 4
Twist filter into the bottom of the reservoir. Do not drop
the filter in from above. Tighten until there is a complete
seal between the filter, blue O-ring and reservoir.
STEP 5
Fill reservoir with cold tap water (directly on to the
filter) and place lid on top. Allow all the water to pass
through the filter before filling again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means
it is time to change your filter.
*For Ready-Read products simply turn on your meter
(while it is docked within the spigot) during dispensing
and get your instant read, every time.
STEP 1
Remove the TDS meter from packaging and test your
tap water. Compare to TDS chart on page 3 to help
give a gauge of filter life.
*For Ready-Read products detach integrated meter
from device.
STEP 2
Remove lid and reservoir from device. Unwrap filter and
remove branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using mild soap
then rise and dry thoroughly. Then rinse the exterior
of your filter with warm water for 30 seconds.
*Reminder please rewash your device with each
filter change.
STEP 4
Twist filter into the bottom of the reservoir. Do not drop
the filter in from above. Tighten until there is a complete
seal between the filter, blue O-ring and reservoir.
STEP 5
Fill reservoir with cold tap water (directly on to the
filter) and place lid on top. Allow all the water to pass
through the filter before filling again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means
it is time to change your filter.
*For Ready-Read products simply turn on your meter
(while it is docked within the spigot) during dispensing
and get your instant read, every time.
READY-READ DISPENSERS ONLY (22, 32, 52 cup):
Align spigot with hole, push into space until lock
engages, and you hear an audible click.
Helpful Hint: Wet blue O-ring prior to assembly
for easier fit.
ZeroWater® PITCHER MODELS: 6, 7, 8 round, 10, 10 round, 10RP, 12, 12RR. ZeroWater® DISPENSER MODELS: 20, 22RR, 30, 32RR, 40, 52RR.
ASSEMBLE YOUR ZEROWATER
DISPENSER QUICKLY AND EASILY
METER DOCKED IN READY-READ DISPENSER
20879-01A/20627 READY READ: 13nal_ZW_RR_Pamphlet_ENG FRENCH 52 cup.ai | smithdesign.com
05.09.23 | ZEROWATER | ZeroWater Cooler Jug Pamphlet | Revision 13nal
AM: JG | AD: MH | DES: tt
13nal
SPREAD 2
ENGLISH - 52cup
1 2
ASSEMBLE YOUR ZEROWATER
PITCHER QUICKLY AND EASILY
STEP 1
Remove the TDS meter from packaging and test your
tap water. Compare to TDS chart on page 3 to help
give a gauge of filter life.
*For Ready-Read products detach integrated meter
from device.
STEP 2
Remove lid and reservoir from device. Unwrap filter and
remove branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using mild soap
then rise and dry thoroughly. Then rinse the exterior
of your filter with warm water for 30 seconds.
*Reminder please rewash your device with each
filter change.
STEP 4
Twist filter into the bottom of the reservoir. Do not drop
the filter in from above. Tighten until there is a complete
seal between the filter, blue O-ring and reservoir.
STEP 5
Fill reservoir with cold tap water (directly on to the
filter) and place lid on top. Allow all the water to pass
through the filter before filling again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means
it is time to change your filter.
*For Ready-Read products simply turn on your meter
(while it is docked within the spigot) during dispensing
and get your instant read, every time.
STEP 1
Remove the TDS meter from packaging and test your
tap water. Compare to TDS chart on page 3 to help
give a gauge of filter life.
*For Ready-Read products detach integrated meter
from device.
STEP 2
Remove lid and reservoir from device. Unwrap filter and
remove branded film or blue cap (where applicable).
STEP 3
Clean your device in warm water using mild soap
then rise and dry thoroughly. Then rinse the exterior
of your filter with warm water for 30 seconds.
*Reminder please rewash your device with each
filter change.
STEP 4
Twist filter into the bottom of the reservoir. Do not drop
the filter in from above. Tighten until there is a complete
seal between the filter, blue O-ring and reservoir.
STEP 5
Fill reservoir with cold tap water (directly on to the
filter) and place lid on top. Allow all the water to pass
through the filter before filling again.
STEP 6
Fill your cup and enjoy.
STEP 7
Once your TDS meter reads 006 that means
it is time to change your filter.
*For Ready-Read products simply turn on your meter
(while it is docked within the spigot) during dispensing
and get your instant read, every time.
READY-READ DISPENSERS ONLY (22, 32, 52 cup):
Align spigot with hole, push into space until lock
engages, and you hear an audible click.
Helpful Hint: Wet blue O-ring prior to assembly
for easier fit.
ZeroWater® PITCHER MODELS: 6, 7, 8 round, 10, 10 round, 10RP, 12, 12RR. ZeroWater® DISPENSER MODELS: 20, 22RR, 30, 32RR, 40, 52RR.
ASSEMBLE YOUR ZEROWATER
DISPENSER QUICKLY AND EASILY
METER DOCKED IN READY-READ DISPENSER