ZIPPER MASCHINEN ZI-MOS145J User Manual (English)

Questions and Answers:

M
Melissa WilsonAug 12, 2025
Why ZIPPER MASCHINEN ZI-MOS145J Brush Cutter engine does not start?
- O
  ocarrilloAug 12, 2025
  There are several reasons why your ZIPPER MASCHINEN Brush Cutter engine might not be starting. It could be due to an incorrect starting sequence, so make sure to follow the correct procedure. Other potential causes include a dirty air filter (clean or replace it), no fuel supply (refuel), a fault in the fuel line (check for kinks or damages), a flooded engine (remove, clean, and dry the spark plug, then pull the cranking rope several times before reinstalling), a disconnected spark plug connector (place it on), or no ignition spark (clean/replace the spark plug and check the ignition cable).
B
blairlauraAug 16, 2025
Why ZIPPER MASCHINEN ZI-MOS145J Brush Cutter does not work with full performance?
- D
  David AndersonAug 16, 2025
  Your ZIPPER MASCHINEN Brush Cutter might not be working at full performance due to a few reasons. It could be overloaded, meaning you're applying too much pressure or the cutting material is too tough. Another possibility is a dirty air filter, which requires cleaning or replacement. The carburetor might also be incorrectly adjusted, but in this case you should contact customer service.
C
Catherine ValdezAug 20, 2025
What to do if ZIPPER MASCHINEN Brush Cutter works with interruptions?
- G
  Gina GravesAug 20, 2025
  If your ZIPPER MASCHINEN Brush Cutter is working with interruptions, the carburetor might be incorrectly adjusted, and you should contact customer service. Another possible cause is a fouled spark plug, which you should clean or replace. Also, check the spark plug connector.
S
Stephen DaughertyAug 23, 2025
Why ZIPPER MASCHINEN Brush Cutter engine starts and stalls immediately?
- H
  hammondbarbaraAug 25, 2025
  If your ZIPPER MASCHINEN Brush Cutter engine starts and stalls immediately, it could be due to an incorrect idle adjustment. In this case, you should contact customer service.
A
Ashley ArnoldAug 28, 2025
How to fix bad cuts with ZIPPER MASCHINEN ZI-MOS145J?
- R
  renee56Aug 28, 2025
  If you're experiencing bad cuts with your ZIPPER MASCHINEN Brush Cutter, it could be due to foreign material wrapped around the sheet or long grass. If there is foreign material wrapped, shut the machine off, wait until the cutter stands still, and remove the winded up material. If there is long grass, then remove the material. Another cause could be a blunt saw blade, which needs to be sharpened or replaced.
G
Gabriela JohnsonAug 31, 2025
Why ZIPPER MASCHINEN ZI-MOS145J produces smoke?
- J
  Joseph WellsAug 31, 2025
  If your ZIPPER MASCHINEN Brush Cutter is producing smoke, it might be due to an incorrect fuel mixture for a 2-stroke engine; use the correct fuel mixture. Another possible cause is an incorrectly adjusted carburetor, for which you should contact customer service.
W
wcrawfordSep 4, 2025
What to do if ZIPPER MASCHINEN ZI-MOS145J Brush Cutter blade rotates but has no power?
- Y
  Yolanda Harris DVMSep 4, 2025
  If the blade of your ZIPPER MASCHINEN Brush Cutter rotates but has no power, make sure the choke is set to OFF.
J
John ScottSep 7, 2025
How to adjust ZIPPER MASCHINEN ZI-MOS145J if blade rotates at idling?
- S
  spencerjonathanSep 7, 2025
  If the blade of your ZIPPER MASCHINEN Brush Cutter rotates at idling, the idle speed might be too high. Adjust to a lower idle speed.