1byone Naturalife - User Manual

Questions and Answers

J
Joshua JenkinsAug 3, 2025
Why is water dripping from my 1byone Iron's soleplate?
- R
  Robert AdamsAug 4, 2025
  If water drips from the holes in the soleplate of your 1byone Iron, it could be due to several reasons: * You might be using steam before the iron is hot enough. Wait until the temperature indicator light turns off. * You might be using the Steam Burst button too frequently. Press the Steam Burst button at 4-second intervals. * The iron may have been stored horizontally without being emptied and without being set to the correct position. See the section “Storing the Iron.”
P
patricia13Aug 10, 2025
What to do if the soleplate of my 1byone Iron is dirty and stains linen?
- J
  John MarshAug 10, 2025
  If the soleplate of your 1byone Iron is dirty or brown and stains your linen, it could be due to: 1. Ironing with an inappropriate temperature selection (temperature too high). Clean the soleplate (see the section 'Soleplate Care') and select the appropriate temperature. 2. Ironing over a printed area of a garment. Never iron printed areas or applications. Always iron the reverse side of such a garment. 3. The soleplate being dirty. Check the soleplate before ironing and clean the soleplate if necessary (see the section 'Soleplate Care').
E
elizabethhowellAug 15, 2025
Why does my 1byone Iron leave brown streaks on my clothes?
- C
  cody06Aug 15, 2025
  If brown streaks come through the holes in the soleplate of your 1byone Iron and stain the linen, it may be because: * You are using ironing water additives (e.g., scented water, starch). Never use ironing water additives as these will permanently damage your steam iron. * You are not using the right type of water. Perform a self cleaning operation and see the section “What water to use?”. * Your linen has not been rinsed sufficiently, or you have ironed a new garment before washing it. Make sure that your laundry is rinsed sufficiently to remove any deposits of soap or chemical products on new clothes.
C
Chase EnglishAug 21, 2025
Why does steam or water leak when filling my 1byone Iron?
- J
  Jennifer KellerAug 21, 2025
  If steam or water comes from your 1byone Iron as you finish filling the tank: * Ensure the Variable Steam Dial is in the correct position. * Avoid overfilling the water tank, never exceed the Max level.
A
Angela AllenAug 28, 2025
How to fix the spray function on my 1byone Iron?
- J
  Jerry CollierAug 28, 2025
  If the spray function on your 1byone Iron is not working, ensure the water tank is filled to the Max level.

Summary

Important Safety Instructions

Polarized Plug (For US Only)

Explains the polarized plug for reduced electric shock risk.

Tamper-Resistant Screw

Warns against removing the outer cover due to tamper-resistant screws.

How to Use

Filling with Water

Tilt iron and pour water into the tank until MAX level. Refill as needed.

Setting the Temperature

LCD Display

Shows fabric types and temperature levels for ironing.

Dry Ironing

Ironing with Steam

Burst of Steam

Horizontal

Use to remove stubborn creases.

Vertical

Use for removing wrinkles from hanging clothes and drapes.

Using Spraying Mist

3-Way Auto Shutoff

Emptying the Water Tank

Automatic Anti-Calc Function

Auto-Cleaning System

Cleaning the Exterior

Soleplate Care

Storing the Iron

Tips for Best Ironing Results

Troubleshooting

Specifications

Disposal

Disposal of the Product

Instructions on how to properly dispose of the product and its packaging.

Customer Service

1byone Naturalife Specifications

General

Filter Type	HEPA
CADR (Smoke)	135 CFM
CADR (Dust)	135 CFM
CADR (Pollen)	135 CFM
CADR	135 CFM
Noise Level	30 dB
Noise Level (Max)	50 dB
Timer	Yes (2/4/8 hours)
Voltage	120V