2gig Technologies 2GIG-BRDG1-900 User Manual

Copyright © 2014 Linear LLC 1
2GIG-BRDG1-900
GO!BRIDGE IP COMMUNICATOR
INSTALLATION INSTRUCTIONS
TheGo!BridgeIPCommunicator™(2GIG‐BRDG1‐900)providesInternet
connectivitybetweenthemonitoringservice’sCentralStationandthe
Go!Control®Panel,whenthepanelisusedasahouseholdburglaralarm
system.
Itsupportsautomaticfirmwareupdates,providesinteractivesecurity
services,andincreasessupervisionusingsignal‐forwardingtotheCentral
Station.For
wirelesscommunicationwiththeControlPanel,the900MHz
TransceiverModule(2GIG‐XCVR)mustbeinstalledinthepanel.For
Internetaccess,theGo!Bridgemustbeconnectedtothelocalnetwork
routerusinganEthernetcable(notprovided).
Contents
Verifythatthepackageincludesthefollowing:
•1—Go!BridgeIPCommunicator
•1—5VDCUSBMini‐BPowerSupply
•1—Stand
• 1—PlasticPowerSupplyBracket(includesSelf‐AdhesiveBacking
andZipTie)
•1—WallSock etScrewforPowerSupplyBracket
• 2—PhillipsHeadScrewsandWallAnchors(tomountunitonwall)
•4—Self‐AdhesiveVinylBumpersforuseonunitorstand
Requirements
Befor eyouinstall,program,andtesttheGo!BridgeIPCommunicator,
ensurethecontrolpanelbeingpairedwiththeGo!BridgeIP
Communicatormeetstheserequirements:
•FirmwareVersion1.12(orhigher)
•2GIG‐XCVR900MHzTransceiver
IMPORTANT: ForcompliancewithUL1023:HouseholdBurglar‐
AlarmSystemUnits,theGo!Bridgemustbeinstalledinthe
sameroomastheInternetmodemorrouter.
NOTE: Toprotectdatasentviathelocalwirelessnetwork,itis
recommendedthatyouinstalltheGo!BridgeIPCommunicatoron
alocalnetworkwhereeitherWPA(Wi‐FiProt ectedAccess)or
WPA2(Wi‐FiProtectedAccessII)encryptionisalreadyenabled.
Afterinstalling,programming,andtestingtheGo!BridgeIP
Communicator,youwillneedtoregisteranewcustomerwiththethird‐
partymonitoringservice.SeeRegistrationonpage3.
Figure 1 Go!Bridge Front View—LED Indicators and Learn Button
Powering ON the Go!Bridge IP Communicator
UsethesestepstopowerONtheGo!BridgeIPCommunicator:
1 Attachthepowersupplytothebracket(provided)asfollows:
1a Insertthepowersupplyintotheenclosureontheplasticbracket.
SeeCinthefigurebelow.
1b Securethepowersupplytotheretainingbracketbythreadinga
ziptiethroughthebracket’sslots.SeeDinthefigurebelow.
1c Removethestripfromtheself‐adhesivebackingonthepower
supplybracket.
1d Affixtheadhesiveonthebrackettothewalloutlet.Thensecure
thebrackettotheoutletwiththewallsocketscrew(provided).
NOTE: AlwaysusetheprovidedpowersupplybracketintheUnited
States(andothercountrieswhereitisrequired).Canadadoesnot
requirethepowersupplyretainingbracket.
Figure 2 Power Supply and Bracket
2 ConnecttheGo!Bridgetothepowersource.
NOTE: DonotconnectanEthernetcabletotheGo!BridgeIP
Communicatoratthistime.Youwillconnectthecablewhen
completingthestepsinProgrammingtheGo!BridgeIP
CommunicatorintotheControlPanel.
3 (Optional)Placethestand(provided)onacounter,desktop,orother
flatsurface.SettheGo!BridgeIPCommunicatorinthestand.
NOTE: Toprotectsurfacesfromdamage,affixtheself‐adhesivevinyl
bumperstotheunitorstand.
4 Verifythatthetwo(2)LEDsontheGo!BridgeIPCommunicator
illuminateinRED.SeeFigure1Go!BridgeFrontView—LEDIndicators
andLearnButtononpage1.
A NetworkLED
B 900MHzLED
C LearnButton
A 110VWallOutlet
B PlasticPowerSupplyBracketwithAdhesiveBacking
C ACPowerSupply
D ZipTie

2gig Technologies 2GIG-BRDG1-900 Specifications

General

Brand	2gig Technologies
Model	2GIG-BRDG1-900
Category	Network Router
Language	English

Summary

Installation Instructions

Powering ON the Go!Bridge IP Communicator

Steps to attach the power supply to the bracket and connect it to the outlet.

Requirements

Prerequisites for installing and programming the Go!Bridge IP Communicator.

LED Indicators

Explanation of the status lights on the Go!Bridge IP Communicator.

Programming and Configuration

Programming the Go!Bridge IP Communicator into the Control Panel

Steps to place the control panel and Go!Bridge into learning mode.

Configuring Go!Bridge IP Communicator Settings

Setting up network device ports and broadband failure alerts.

Post-Installation Checks

Verifying the Settings

How to verify the Go!Bridge IP Communicator settings on the panel.

Testing

Testing the network connection to the third-party monitoring service.

Registration

Instructions for registering the Go!Bridge with the monitoring service.

SPECIFICATIONS

REGULATORY INFORMATION

Wireless Product Notice

General limitations and observations for radio devices.

FCC Notice

FCC compliance rules and interference guidelines for the device.

Industry Canada (IC) Compliance

LIMITED WARRANTY