What to do if the power level display of my 3M Unitek Ortholux Luminous Curing Ligh Medical Equipment handpiece flashes red?
If the power level display of your 3M Unitek Medical Equipment handpiece flashes red, the exposure is interrupted, and the handpiece goes to sleep mode, it means the battery lacks sufficient charge. Place the handpiece in the charger and recharge the battery.
Why my 3M Unitek Ortholux Luminous Curing Ligh Medical Equipment handpiece cannot be turned on after long time without use?
If your 3M Unitek Medical Equipment handpiece has not been used for a long time and now it cannot be turned on, it is likely that the battery does not have enough charge. Place the handpiece in the charger and recharge the battery.
Why does the charge level display on my 3M Unitek Ortholux Luminous Curing Ligh Medical Equipment glow red?
If the charge level display on your 3M Unitek Medical Equipment handpiece glows red steadily, it means the remaining battery charge is only adequate for about 20 3-second exposure cycles. Place the handpiece in the charger and recharge the battery.
What to do if my 3M Unitek Medical Equipment handpiece overheats during light emission?
If you get an error signal during light emission in extended mode with your 3M Unitek Medical Equipment, it means the handpiece has overheated. Allow the handpiece to cool down for a minimum of 1.5 minutes before starting a new light emission. The handpiece can be used again once the START button successfully activates the light. A 2-minute cooling-off time in the air typically corresponds to 1 minute of operating time.
Why light emission does not start when pressing START button on 3M Unitek Ortholux Luminous Curing Ligh?
If the light emission does not start when you press the START button on your 3M Unitek Medical Equipment and an error signal sounds, it indicates that the handpiece has become overheated. Allow the handpiece to cool down. The handpiece can be used again once pressing the START button successfully activates the light. During the cooling-off period immediately after the acoustical signal has gone off, a 2 minute cooling-off time in the air typically corresponds to 1 minute operating time.
What does it mean if the power level display of 3M Unitek Medical Equipment handpiece flashes red in the charger?
If the power level display of your 3M Unitek Medical Equipment handpiece flashes red while it is in the charger, this indicates a charging problem. The battery may be defective or at the end of its useful life. Try removing and re-inserting the battery to reset the unit. If that doesn't work, replace the battery.
Why is the LED on my 3M Unitek Medical Equipment charger flashing red and green when the handpiece is in it?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment flashes alternately red and green while the handpiece is in the charger, it indicates a malfunction during charging. Remove and re-insert the battery to reset the unit. If the problem persists, the battery may be damaged and require replacement.
What to do if the LED on my 3M Unitek Ortholux Luminous Curing Ligh Medical Equipment charger doesn't turn on?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment does not come on even when plugged into an outlet, it could be due to the power outlet not carrying any voltage. Try using a different power outlet. Alternatively, the charger itself may be defective.
Why is the LED on my 3M Unitek Ortholux Luminous Curing Ligh Medical Equipment charger glowing red steadily?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment glows red steadily, it indicates that the charge contact pins in the handpiece or the charger are wet. Dry the charge contact pins, being careful not to bend the flexible charge contact pins in the charger.
Why is the LED on my 3M Unitek Medical Equipment charger flashing red and green when the handpiece is not in it?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment flashes alternately red and green, and the handpiece is not in the charger, it indicates that the charger is defective. Try unplugging and plugging in the charger to reset it.
General| Light Source | LED |
|---|---|
| Light Intensity | 1000 mW/cm² |
| Curing Time | 5-20 seconds |
| Timer Settings | 5, 10, 15, 20 seconds |
| Battery Type | Lithium-ion |
| Wavelength | 430-490 nm |
| Curing Modes | Standard |
| Power Supply | AC 100-240V, 50/60Hz |
Essential safety guidelines for operating the curing light and avoiding health risks.
Emphasizes eye protection and avoiding soft tissue damage from high-intensity light.
Step-by-step instructions for inserting and removing the rechargeable battery from the handpiece.
Explains how to charge the unit's rechargeable battery and the initial charging requirement.
Guides on activating the handpiece and selecting different exposure times for curing.
Instructions on starting/stopping light emission and using the Tack Cure function.
Lists common operational errors and provides corresponding solutions for the handpiece and charger.
Addresses issues related to the charger's LED status and potential malfunctions.
To Next Page
