What to do if the power level display of my 3M Unitek Medical Equipment handpiece flashes red?
If the power level display of your 3M Unitek Medical Equipment handpiece flashes red, and the exposure is interrupted, followed by an error signal, and the handpiece switches to sleep mode, it likely means the battery lacks sufficient charge. To resolve this, place the handpiece in the charger and recharge the battery.
Why the LED showing operating status in the charger of my 3M Unitek Medical Equipment doesn't come on?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment does not come on, first, check if the power outlet carries voltage by using a different outlet. If the issue persists, the charger might be defective and require repair.
What to do if the power level display of my 3M Unitek Medical Equipment handpiece flashes red in the charger?
If the power level display of your 3M Unitek Medical Equipment handpiece flashes red while it is in the charger, it indicates a charging problem. This could be due to a defective battery or one that is at the end of its life. Try removing and re-inserting the battery to reset the unit. If that doesn't work, consider replacing the battery.
Why the LED showing the operating status in the charger of my 3M Unitek Medical Equipment flashes red and green?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment flashes alternately red and green when the handpiece is in the charger, it indicates a malfunction during charging or a damaged battery. Try removing and re-inserting the battery to reset the unit. If the problem continues, replace the battery.
What to do if light emission does not start on my 3M Unitek Medical Equipment?
If the light emission does not start when you press the START button on your 3M Unitek Medical Equipment, and an error signal sounds, it may be because the handpiece has overheated during use. Allow the handpiece to cool down. Once cooled, you should be able to activate the light by pressing the START button again. Remember that a 2-minute cooling-off period in the air typically corresponds to 1 minute of operating time.
What to do if my 3M Unitek Medical Equipment stops during light emission?
If, during light emission in extended mode, an error signal sounds for 2 seconds, the emission stops, and your 3M Unitek Medical Equipment handpiece changes to sleep mode, it indicates that the handpiece has overheated. Allow the handpiece to cool down for at least 1.5 minutes in the air before starting a new light emission. After cooling, you can use the handpiece again once pressing the START button successfully activates the light. Remember that a 2-minute cooling-off period typically corresponds to 1 minute of operating time.
Why my 3M Unitek Medical Equipment handpiece cannot be turned on?
If the handpiece of your 3M Unitek Medical Equipment has not been used for a long time and now it cannot be turned on, it probably means that the battery does not have enough charge. Place the handpiece in the charger and recharge the battery.
How to fix the red charge level display on my 3M Unitek Medical Equipment?
If the charge level display on the handpiece of your 3M Unitek Medical Equipment glows red steadily, place the handpiece in the charger and recharge the battery.
Why the LED showing operating status in the charger of my 3M Unitek Medical Equipment glows red?
If the LED showing the operating status in the charger of your 3M Unitek Medical Equipment glows red steadily, it indicates that the charge contact pins in the handpiece or the charger are wet. Dry the charge contact pins carefully, being careful not to bend the flexible charge contact pins in the charger.
How to increase light intensity of my 3M Unitek Medical Equipment?
If the light intensity of your 3M Unitek Medical Equipment is too low, clean the light guide and the protecting glass in the light guide mounting hole. Please refer to “Cleaning the Light Guide” for instructions.
Covers essential safety guidelines for operation, handling, and potential hazards.
Emphasizes eye protection and restricted light exposure to avoid health consequences.
Advises caution for patients with specific medical conditions like pacemakers or photobiological reactions.
Details device components, LED specifications, and its specific application in orthodontics.
Lists operating voltage, power input, dimensions, weight, and wavelength range.
Outlines initial setup steps including charger connection and light guide preparation.
Instructions for inserting the battery and initial charging for optimal performance.
Guide to powering the unit and selecting desired curing times.
How to activate and deactivate light emission and use the tack cure feature.
Practical advice on curing techniques for various appliances and adhesives.
Procedure for checking light intensity using the integrated testing area on the charger.
Explains device sleep mode and audible signals for status indication.
Lists common errors, their causes, and solutions for resolving issues.
Guidelines for cleaning the light guide, handpiece, and charger for optimal operation.
Instructions for storage, unit disposal, and warranty coverage details.
General| Light Source | LED |
|---|---|
| Battery Type | Lithium-ion |
| Power Supply | AC Adapter |
| Type | Curing Light |
| Light Intensity | 1000 mW/cm² |
| Curing Modes | Standard |
| Timer Settings | 10, 20 seconds |
| Charging Time | Approx. 2 hours |
To Next Page
