3M PELTOR ComTac 7 - Dual Protection Modes; MENU SYSTEM NAVIGATION; ComTac VII Menu Navigation

29
Radio
Volume
Ambient
Listening
Advanced
Settings
4. Pressthe+buttontoconrmandtoaccessAdvanced
settings.
5. Press the - button to move forward in the menu system
until the audio message indicates the sub menu
Bluetooth
®
Functions button to RCU.
6. Pressthe+buttontoconrm.
Note: The PTT II button on the RCU-300 now has the same
function as the F button on the SCU-300.
7.4. DUAL PROTECTION AND EARPLUG
MODE
The Tactical Modular Audio System (TMAS) is designed to
allow dual hearing protection for high noise exposures. The
TEP-300 or a non-electronic (passive) hearing protector can
be worn under the ComTac™ VII to achieve dual hearing
protection. When a non-electronic (passive) hearing
protection device is used, it may be necessary to place the
ComTac™ VII in Earplug Mode to maintain environmental
auditory awareness and communications.
NOTE: The user must achieve an adequate hearing protector
tforbothin-earandover-earhearingprotectorstoreceive
dual protection.
7.4.1. DUAL PROTECTION WITH TEP-300
1. Insert and power-on the TEP-300. Refer to TEP-300 User
Instructions.
2. Place the ComTac™ VII over the ears and power-on. Refer
to ComTac™ VII User Instructions.
3. Power on the SCU-300. Refer to SCU-300 and TMAS User
Instructions.
4. The ComTac™ VII and SCU-300 will automatically detect
the TEP-300.
7.4.2. DUAL PROTECTION WITH PASSIVE HEARING
PROTECTOR AND EARPLUG MODE
Earplug Mode is useful when dual hearing protection is
required, and the user prefers a passive hearing protection
device, such as the 3M™ E-A-R™ Classic™ Earplug.
WARNING! DO NOT use the headset in Earplug Mode
withoutproperlyttedearplugsundertheearcups,asthe
increase in audio volume may reach an unsafe level. Failure
towearproperlyttedearplugswhileoperatinginEarplug
Mode may result in hearing loss or injury.
1. Properlytthepassivehearingprotector.
2. Place the ComTac™ VII over the ears.
EN
If the headset is powered off:
3. Press and hold the + button until an audio message says
“Power on”.
4. Keep pressing the + button until an audio message
conrms“EarplugMode”.
5. Turn off ComTac™ VII to turn off the Earplug Mode.
If the headset is powered on:
6. Press and hold the + button until an audio message says
“Power off”.
7. Keep pressing the + button until an audio message
conrms“EarplugMode”.
8. Turn off ComTac™ VII to turn off the Earplug Mode.
~ 7 sec
NOTE: Theheadsetwillrstindicatethattheproductisoff.
Keep pressing the + button until an audio message indicates
Earplug Mode.
8. TO NAVIGATE THE MENU SYSTEM
8.1. COMTAC™ VII
Press the + button and the - button at the same time to enter
the menu system. The headset will indicate that the user has
entered the menu with an audio message “Menu”. For more
information about the menu, refer to “9. Menu functions
ComTac™ VII”
Menu
~ 0.5 sec
• Short press the - button to move forward in the menu
system.
• Short pressthe+buttontoconrmortoaccessa
sub-menu.
Note: Menu options and settings will be heard as an audio
message in the headset.
To exit the menu, press the + and - buttons at the same time.
The headset will automatically exit the menu if no button is
pressed for 10 seconds.
EN