Need help?Do you have a question about the 4O3A Antenna Genius and is the answer not in the manual?
Details the new generation of Antenna Genius software, focusing on stability, reliability, and extended features.
Important notes on API and network protocol changes for version 4 and compatibility with custom software.
Instructions on how to back up the Antenna Genius configuration before firmware upgrades.
Comprehensive details on manufacturer, model, functionality, ports, network, power, frequency, isolation, CPU, and case.
Information on FCC compliance and guidelines for preventing radio frequency interference.
Declaration of compliance with European Community EMC standards.
Manufacturer's right to make changes without prior notice.
Details coverage, exclusions, and procedures for warranty service.
Lists all registered trademarks related to the product and its ecosystem.
Copyright notice and reproduction restrictions for the publication.
Explains five methods for controlling the Antenna Genius: FlexRadio, manual, BCD, and Pin-to-Port.
Details using the AG for Single Operator 2 Radio (SO2R) and multi-operator setups with FLEX-6000.
Details the microprocessor, networking, and hardware capabilities of the Antenna Genius.
Explains the AG App, FlexRadio integration, and automatic band selection via SSDR API.
Describes the connectors and LEDs located on the front panel of the device.
Details the LAN, DE-15 ports, power input, OM module connector, and DIP switches.
Highlights DC power connector and RCA ports for PTT input/output.
Guidance on selecting an optimal location for the Antenna Genius in a station setup.
Instructions for connecting the 12-15 VDC power supply, including fuse recommendations.
Information on using Cat5e/Cat6 cables for network connectivity and best practices.
Explanation of DIP switch functions, particularly for firmware recovery mode.
How to configure and use the Antenna Genius via LAN for band data acquisition from FlexRadio.
Details on using BCD signals for band data, including pinouts and compatible radios.
Instructions for using Pin-to-Port for manual antenna switching and its pinout.
Configuration for automatic band selection based on priority of data sources.
Using manual mode for testing and debugging antenna configurations.
Guide to downloading, installing, and launching the Antenna Genius Windows application.
Using DHCP to automatically set the network address for the AG device.
Steps to launch the AG application after installation.
Accessing and viewing detailed status and configuration information of the Antenna Genius.
Procedure to check if the AG firmware is up-to-date and instructions for updating.
Steps for initial setup and configuration of the Antenna Genius via the control window.
Navigating the main configuration menu for device settings and options.
Enabling or disabling the 'Always on Top' feature for the AG application window.
Displaying the current status of all output ports on the relay module.
Accessing the main configuration settings for the Antenna Genius device.
Setting a unique name for the Antenna Genius device for easier identification.
Assigning names and usable bands to each antenna port.
Configuring antennas for RX, TX, or Inband operation across multiple bands.
Assigning custom keyboard shortcuts for quick antenna selection.
Configuring the optional OM module for relay switching and automation.
Organizing output relays into groups for controlled activation and binding to antenna ports.
Assigning keyboard shortcuts to activate specific relay outputs.
Customizing frequency spans for different bands and defining custom bands.
Setting up the connection and control between Antenna Genius and FlexRadio devices.
Configuring the Antenna Genius to use BCD signals for band data.
Using Pin-to-Port for direct control of the Antenna Genius, similar to a classic switch.
Configuring IP address, subnet mask, gateway, and remote password for network operation.
Enabling and configuring stacking for multiple Antenna Genius units to expand antenna capacity.
Advanced settings including inband port, band protection, import/export, reboot, and factory reset.
Adding static entries for fixed IP addresses and setting up remote operation.
Configuring the AG utility to automatically connect to the AG device on startup.
Controlling OM modules for relay switching, with details on logical and physical outputs.
Description of the SSC OM Module hardware and its relay outputs.
Steps to connect the OM module to the Antenna Genius using an RS232 cable.
Reference to configuring the OM module via the Output Relays Designer.
Procedure to recover an unresponsive Antenna Genius device using the bootloader and firmware recovery.
To Next Page
General