A'OK AC202-02 - User Manual

-40℃～+85℃
AC202-02
38KHZ
2.Parameters
≤500W
230VAC 50Hz
AC202-02Radio Receiver Manual V 1 .0.2
1.Features
!
3.Wiring
AC118-01
IR Remote Control
≤
80M
AC112-04
AC104-02
AC118-01
Infrared control
AC118-01
AC104-02
AC112-04
AC202-02
Receiver
433.92HZ
AC104-02
RF Remote control
IR
RF
≤
8M
AC112-04
Warning
Power off before wiring
Avoid static damage Earth wire must be
connected well and correctly
To keep good control
range, avoid connect
metal parts
Manual switch wiring terminal
+5V:IR voltage
IR:IR signal
U:UP/DOWN(brown)
N:Neutral(Blue)
E: Earth (Yellow/Green)
L:Live(Brown)
Power wiring terminal
E:Earth (Green/Yellow)
N:Neutral(Blue)
L:UP /Down(Black)
R:Down/UP (Brown)
Motor wiring terminal
Model No. Voltage Temperature Receive distance Loading Power Operation Mode
Manual pulse Switch
Work with all A-OK tubular motor
SMT machine automatical assembly, dampproof craft
Support of IR,RF,Manualcontrol and DC12V trigger
Work with motorized projection screen, motorized
awning, roller blinds etc
RF Control Manual Switch
Frequency
IR
RF RF, IR and Manual
control, DV12V trigger
signal light
IR receive head
program button
sw1 up
sw2 stop
sw3 down
IR transmitter
projector
IR receive head
Manual switch and IR receive
N:Noutral(Blue) E:Earth(Yellow/Green)
L:Live(brown)
N:Noutral(Blue) E:Earth(Yellow/Green) L:UP/Down(Black) R:Down/UP(Brown)
RF transmitter
Motor
power input
Manual switch operate instruction:
1:press up key less than1's the motor
run up,more than 1's then loose up,
the motor stop
2:press down key less 1's and motor
run down,more than 1's loose and
motor stop
Wiring
NC:empty terminal
GND: earth wire
+12V:DC trigger
out-link projector terminal
S:stop(green)
D:Down/up(black)
G:Neutral(BLUE)
Me
t
a
l Pa
rt
s
up
stop
down

Summary

Product Features

Technical Parameters

Wiring Connections

Motor Wiring Terminal

Details for connecting the motor, including earth, neutral, and phase wires for up/down.

Power Wiring Terminal

Connection points for power input, specifying neutral, earth, and live terminals.

Manual Switch Wiring Terminal

Wiring details for manual switch control, including UP/DOWN and stop signals.

Out-link Projector Terminal

Terminal for projector connection, including GND and +12V trigger.

Operational Warnings

Power Off Before Wiring

Ensure power is disconnected before performing any wiring operations.

Avoid Static Damage

Take precautions to prevent electrostatic discharge damage during handling.

Correct Earth Wire Connection

Proper and secure connection of the earth wire is essential for safety and performance.

Maintain Control Range

Maintain optimal control range by avoiding proximity to metal parts.

Function Adjustment

IR Remote Control Program

IR remote control must be programmed within effective range for operation.

Receiver State Reset

Receiver reverts to original state if no operations occur within 10 seconds.

Transmitter Limit

A maximum of 20 IR or RF transmitters can be programmed per receiver.

Motor Working Time Limit

The longest continuous working time for the motor is limited to 5 minutes.

Programming and Deletion

Program Setting

Procedure for programming the receiver, including selecting channels before operation.

Delete All Codes

Method to erase all programmed IR and RF codes from the receiver.

Delete Single Code

Process for removing a specific programmed code from the receiver.

Direction Change

Change Motor Direction

Instructions on how to change the operating direction of the motor.

Troubleshooting

Receiver Not Responding

Troubleshoot when the transmitter works but the receiver shows no action.

Transmitter LED Issues

Diagnose problems with the transmitter's LED brightness or status.

Motor Not Working

Check motor wiring and condition if the control system works but the motor does not.

Incorrect Motor Movement

Resolve issues where pressing 'up' runs 'down' and vice-versa.

A'OK AC202-02 Specifications

General

Brand	A'OK
Model	AC202-02
Category	Receiver
Language	English