ABB HT575675 - User Manual

132 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operation Manual

ABB Turbocharging



ABB Turbo Systems Ltd

CH 5401 Baden

Type TPS48-F32 HT575675

n

Mmax

1029 t

Mmax

680

n

Bmax

978 t

Bmax

650

1/s °C

SOLD08 00180 12 60 60

Year 2017

made in Switzerland

Application according to

the Operation Manual

kg

HZTL2412 English

TPS48-F32

Original Operation Manual

Table of Contents

Questions and Answers

A
Alvin ThompsonSep 3, 2025
What to do if ABB HT575675 has charge air pressure too low?
- H
  Hayley MeadowsSep 3, 2025
  If the charge air pressure is too low, there could be several reasons. The air receiver or the gas piping between the engine and the turbine might be leaking. A poorly adjusted injection system also can cause this issue, so correct it. The manometer display might be providing a wrong reading, so replace the manometer, or the line to the manometer might be leaking, so repair the leak. A contaminated filter silencer causing excessive loss of pressure can also be the reason, so clean it. In some cases, the compressor/turbine might be damaged, which requires contacting an ABB Turbocharging Service Station. High exhaust counterpressure can also cause low charge air pressure, so clean or repair the boiler or exhaust silencer.
S
Susan SimsAug 25, 2025
Why is the charge air pressure too low in my ABB charger?
- D
  Donna FreemanAug 25, 2025
  If the charge air pressure is too low in your ABB charger, several factors could be responsible: * Air receiver leaking: Make repairs. * Gas piping between the engine and the turbine leaking. * Poorly adjusted injection system: Correct it. * Poorly adjusted valve control. * Manometer display wrong: Replace the manometer. * Line to manometer leaking: Repair the leak. * Contaminated filter silencer: Clean it because it causes excessive pressure loss. * Damaged compressor/turbine: Contact an ABB Turbocharging Service Station. * High exhaust counterpressure: Clean or repair the boiler or exhaust silencer.
J
Jacob GentryAug 25, 2025
Why is the charge air pressure too high in my ABB charger?
- L
  Linda AveryAug 26, 2025
  If the charge air pressure is too high in your ABB charger, it may be due to: * A malfunctioning injection system: Repair it or contact the manufacturer. * A poorly adjusted injection system: Correct it. * Engine performance higher than expected: Check engine performance. * Manometer display wrong: Replace the manometer.
L
Laura CraigSep 10, 2025
Why is my ABB HT575675 Industrial Equipment having a sluggish start-up?
- H
  Heather TownsendSep 10, 2025
  If your ABB Industrial Equipment experiences a sluggish start-up, it could be due to a few reasons. The turbocharger might be contaminated and need cleaning. Alternatively, there may be damage to the bearing, in which case you should contact an ABB Turbocharging Service Station. Other potential causes include a rubbing rotor or a foreign object present in the turbocharger.
M
Mary VillanuevaSep 17, 2025
What to do if lubricating oil pressure is too low in ABB Marine Equipment?
- D
  David MoonSep 17, 2025
  If the lubricating oil pressure is too low, it could be due to several reasons. The oil filter might be heavily contaminated (clean it), the oil pump in the lubricating system could be defective (check / replace it), the manometer display might be wrong (replace the manometer), or the rotor axial clearance might be too large (contact an ABB Turbocharging Service Station).
M
Mr. Richard RichardsSep 6, 2025
What to do if the charge air pressure is too low in ABB HT575675 Industrial Equipment?
- C
  Chad Cabrera Jr.Sep 7, 2025
  If your ABB Industrial Equipment experiences charge air pressure that is too low, several factors could be responsible. You can repair any leaks in the air receiver or correct a poorly adjusted injection system. Additionally, you should replace the manometer if the display is wrong, or repair the leak if the line to the manometer is leaking. Clean the filter silencer if it is contaminated, causing excessive pressure loss. Finally, clean or repair the boiler or exhaust silencer if the exhaust counterpressure is too high.
R
Rebecca BrownAug 31, 2025
What to do if ABB Industrial Equipment has vibration?
- K
  kcookAug 31, 2025
  If your ABB Industrial Equipment is vibrating, it could be due to rotor unbalance, in which case you should contact an ABB Turbocharging Service Station. Other potential causes include a damaged turbine or compressor, or a damaged bearing.
A
Amy LopezSep 23, 2025
What causes increase in speed in ABB Marine Equipment?
- J
  jamesjohnsonSep 23, 2025
  An increase in speed can be caused by a heavily contaminated nozzle ring (with 4-stroke application) (contact an ABB Turbocharging Service Station).
J
Joshua JordanSep 13, 2025
What to do if ABB HT575675 Industrial Equipment has rubbing of rotating parts?
- J
  John NunezSep 13, 2025
  If you suspect rubbing of rotating parts in your ABB Industrial Equipment, and you're unsure about the extent of the rubbing, it's best to contact an ABB Turbocharging Service Station. They can perform a dimension check to assess the situation.
S
Sara GibsonAug 27, 2025
What causes fouling of the compressor in my ABB charger?
- J
  Joseph MoralesAug 28, 2025
  Fouling of the compressor in your ABB charger, due to the feeding in of ventilation gases, may result from: * Heavy fouling of the compressor components: Clean compressor. * Material of compressor wheel corroded: Check the fuel and its corrosive components, and change fuel if necessary.

ABB HT575675 Specifications

General

Brand	ABB
Model	HT575675
Category	Industrial Equipment
Language	English

Related product manuals