ABB Relion RED615 - Page 23

Table 4: Analog inputs
IEC 61850 LN.DO.DA AFL-Common SA name Description Scaling function Argument 1
(min value)
Argument 2 (max value)
Argument 3 Argument 4
CB position
CBCSWI1.Pos.stVal CBXCBR1.POSITION CB Switch position (4-pole), stVal Ratio 0 3 0 3
Phase current measurements
CMMXU1.A.phsA.instCVal.mag.f CMMXU.I_INST_A Phase currents, phsA.instCVal.mag.f Ratio 0 40 0 4000 CMMXU1.A.phsB.instCVal.mag.f CMMXU.I_INST_B Phase currents, phsB.instCVal.mag.f Ratio 0 40 0 4000 CMMXU1.A.phsC.instCVal.mag.f CMMXU.I_INST_C Phase currents, phsC.instCVal.mag.f Ratio 0 40 0 4000
Sequence of current measurements
CSMSQI1.SeqA.c1.instCVal.mag.f CMSQI.I1_INST Positive Sequence Current, c1.instCVal.mag.f Ratio 0 40 0 4000 CSMSQI1.SeqA.c2.instCVal.mag.f CMSQI.I2_INST Negative Sequence Current, c2.instCVal.mag.f Ratio 0 40 0 4000 CSMSQI1.SeqA.c3.instCVal.mag.f CMSQI.I3_INST Zero Sequence Current, c3.instCVal.mag.f Ratio 0 40 0 4000
Autoreclosing
DARREC1.AutoRecSt.stVal DARREC1.STATUS DARREC1, Auto Reclosing Status, stVal Ratio -2 4 -2 4 DARREC1.ShotPntr.stVal DARREC1.SHOT_PTR DARREC1, Shot pointer value, stVal Ratio 0 65535 0 65535
Disconnector positions
DCSXSWI1.Pos.stVal DCSXSWI1.POSITION Disconnector 1 position (4-pole), stVal Ratio 0 3 0 3 DCSXSWI2.Pos.stVal DCSXSWI2.POSITION Disconnector 2 position (4-pole), stVal Ratio 0 3 0 3 DCSXSWI3.Pos.stVal DCSXSWI3.POSITION Disconnector 3 position (4-pole), stVal Ratio 0 3 0 3 ESSXSWI1.Pos.stVal ESSXSWI1.POSITION Earth switch position (4-pole), stVal Ratio 0 3 0 3
Device diagnostics
LPHD1.NumCmpChg.stVal - Number of composition changes, stVal Ratio 0 65535 0 65535 LPHD1.NumPwrUp.stVal - Number of Power ups, stVal Ratio 0 65535 0 65535 LPHD1.PhyHealth1.stVal - Latest Warning code, stVal Ratio 0 65535 0 65535 LPHD1.PhyHealth2.stVal - Latest Fault code, stVal Ratio 0 65535 0 65535 LPHD1.WacTrg.stVal - Number of watchdog device resets detected, stVal Ratio 0 65535 0 65535
LPHD1.WrmStr.stVal - Number of warm starts, stVal ratio 0 65535 0 65535 disturbance recorder diagnostic
RDRE1.FltNum.stVal - Disturbance recorder, Number of recordings, stVal Ratio 0 65535 0 65535 RDRE1.MemUsed.stVal - Disturbance recorder, Rec. memory used, stVal Ratio 0 100 0 100
Residual current and voltage measurements
RESCMMXU1.A.res.instCVal.mag.f RESCMMXU.I0_INST Residual current, res.instCVal.mag.f Ratio 0 40 0 4000 RESVMMXU1.PhV.res.instCVal.mag.f RESVMMXU.U0_INST Residual voltage, res.instCVal.mag.f Ratio 0 4 0 400
Circuit breaker condition monitoring values
SSCBR1.OpCntr.stVal SSCBR1.NO_OPR Number of CB operation cycle Ratio 0 99999 0 99999
Thermal protection
T1PTTR1.Tmp.mag.f - T1PTTR1, Temperature Ratio -100 9999.9 -1000 99999 T1PTTR1.TmpRl.mag.f - T1PTTR1, Relative temperature Ratio 0 99.9 0 999
1MRS756879 A Section 2
DNP3 data mappings
RED615 17
Point List Manual