ABBREE AR-M6 - User Manual

To Next Page

1.FUNCTIONS & FEATURES

2.PRECAUTIOMS

3.KNOW ABOUT THIS RADIO 4.HOW TO USE THIS RADIO

2.1

You are adviced to check radio version first before connect power cable:

◆

12V version radio

: Your radio must be supplied with a continued current

of 12 volts.

2.2

Please install the antenna (connect to the location“B”on the back panel

of the radio) and set the SWR (Standing Wave Ratio) before transmitting.

Failure to do so may result in destruction of the power amplifier, which is

not covered by the guarantee.

◆

AM and FM mode

◆

VOX

◆

CTCSS/DCS

◆

VOX

◆

SQ and ASQ Control

◆

Full Channel SCAN

◆

EMG Channel CH9/19

1 2 3

4.1

Power On/Off the Radio

....................................................................

(1)

Turn VOL knob clockwise to power on the radio, the LCD displays

channel number.

(2)

Turn VOL knob anti-clockwise, until hear "Ka Ta", the radio is

powered off.

4.2

Volume Control

...................................................................................

Turn VOL knob

clockwise to increase volume, anti-clockwise to decrease

volume.

4.3

ASQ / SQ Control

...............................................................................

※ASQ

(Automatic Squelch Control)

Turn SQ knob

anti-clockwise into ASQ position. LCD displays " ". No

repetitive manual adjustment and a permanent improvement between the

sensitivity and the listening comfort when ASQ is active. This function can

be disconnected by turning the switch clockwise. In this case the squelch

adjustment becomes manual again. "

" disappears from LCD.

※SQ

(Manual squelch)

Turn the SQ knob

clockwise to the exact point where all background

noises disappear. This adjustment should be done with precision as, if set

to maximum (fully clockwise), only the strongest signals will be received.

4.4

▼CH/▲CH

...........................................................................................

※Channel Selector

(short press)

(1)

These keys allow increasing or decreasing a channel. A beep sounds

each time the channel changes.

(2)

Hold or can fast change working channel.

※Scan

(very long press)

(1)

Press and hold the or key for 7 seconds or until a beep sounds

to start scan function, LCD displays " ".

(2)

Short press or key to change scan direction during scan.

(3)

Short press or [

PTT

] key to exit scan function.

3.1

Function location

CB RADIO

Instruction Manual

145

3 7 6 8 10 9

1 POWER ON/OFF ~ VOLUME CONTROL

2 SQUELCH~ASQ (Automatic Squelch Control)

3 MICROPHONE JACK

4 LCD

5 MODE ~ KEYPAD LOCK

6 CTCSS/DCS ~ CTCSS/DCS SET

7 EMERGENCY CHANNEL ~ RESET

8 CHANNEL SELECTOR

9 CHANNEL SELECTOR

10 VOX ~ VOX SET

A ANTENNA JACK

B EXTERNAL SPEAKER JACK

C POWER CONNECTION

D PTT SWITCH

AR-M6

Need help?

Do you have a question about the ABBREE AR-M6 and is the answer not in the manual?

Summary

Radio Precautions and Setup

Radio Version and Power Supply Check

Verify radio version before connecting power, ensuring 12V compatibility.

Antenna Installation and SWR Setting

Install antenna and set SWR before transmitting to prevent amplifier damage.

Radio Function Location Overview

Function Location Identification

Diagram and labels identifying radio controls, ports, and display elements.

Operating the CB Radio

Power, Volume, and Squelch Controls

Instructions for powering on/off, adjusting volume, and using SQ/ASQ.

Channel Selection and Scan Functions

How to change channels, perform fast channel changes, and initiate scan.

Mode Switching and Keypad Lock

Switching between AM/FM modes and locking/unlocking the keypad.

Tone Squelch (TSQ) Settings

Enabling and setting CTCSS tones or DCS codes for squelch.

Emergency Channels and VOX Function

Accessing emergency channels (CH9/CH19) and configuring VOX function.

External Speaker and Factory Reset

Connecting an external speaker and restoring factory default settings.

Regulatory Information

FCC Compliance Statements

Device compliance with FCC Part 15 rules and conditions for operation.

RF Exposure and Separation Distance

Information on safe operation distances for RF exposure compliance.

The ABBREE AR-M6 is a CB radio designed for reliable communication, featuring both AM and FM modes. It offers a range of functionalities including VOX (Voice Operated eXchange), CTCSS/DCS (Continuous Tone-Coded Squelch System/Digital Coded Squelch) for selective calling, and SQ/ASQ (Squelch/Automatic Squelch Control) to manage background noise. The radio supports full channel scanning and includes dedicated emergency channels (CH9/19) for quick access in critical situations.

Function Description:

AM and FM Mode: The radio supports both Amplitude Modulation (AM) and Frequency Modulation (FM) for versatile communication. Users can switch between these modes using the MODE key.
VOX: This feature allows for hands-free operation by transmitting when the user speaks into the microphone. The VOX function can be enabled/disabled and its sensitivity (LE) and delay time (TI) can be adjusted to optimize transmission quality and prevent abrupt cut-offs.
CTCSS/DCS: These systems provide selective calling, allowing users to hear only transmissions with a matching tone or code. The CTCSS/DCS function can be enabled/disabled and configured, with 38 CTCSS tones (001-038) and 104 DCS codes (001-104) available. This feature is only active in FM mode.
SQ/ASQ Control:
- ASQ (Automatic Squelch Control): By turning the SQ knob anti-clockwise to the ASQ position, the radio automatically adjusts squelch levels, providing a balance between sensitivity and listening comfort without manual intervention. The LCD displays "AC" when active.
- SQ (Manual Squelch): Users can manually adjust the squelch by turning the SQ knob clockwise until background noises disappear. This allows for precise control over which signals are received, with higher settings filtering out weaker signals.
Full Channel Scan: The radio can scan through all available channels. This function is activated by a long press of the CH or ACH keys, and the scan direction can be changed during scanning.
EMG Channel (CH9/19): Dedicated keys provide quick access to emergency channels 9 and 19. Repeated presses toggle between these channels and return to the last normal channel.
Keypad Lock: The MODE key can be used to lock the keypad, preventing accidental changes to settings. In lock mode, all keys except the PTT (Push-to-Talk) switch are disabled.
Volume Control: The VOL knob controls the audio output volume.

Important Technical Specifications:

Modulation Mode: AM/FM
Frequency Range: 26.965 - 27.405 MHz
Frequency Tolerance: ±5.0 ppm
Input Voltage: 13.8V
Dimensions: 140 x 161.5 x 41 mm
Weight: 608g
Operating Temperature Range: -20°C to +50°C
Current Drain:
- Transmit: 3A MAX
- Receive (Squelched): 0.3A
- Receive (VOL Max): 0.7A
Antenna Connector: UHF, SO-239
Power Output: 4 Watts (FM/AM)
Transmission Interference: Inferior to 4nW
Frequency Response (TX/RX): 300 - 3000 Hz
Modulated Signal Distortion: Inferior to 5%
Output Impedance: 50 ohms
Receiver Sensitivity: Less than 1uV for 10dB (S+N)/N
Image Rejection: 70dB
Adjacent Channel Rejection: 60dB
IF Frequencies: 1st 10.695MHz, 2nd 455KHz
Automatic Gain Control (AGC): Less than 10dB change in audio output for inputs from 10 to 50000uV
Squelch: Less than 1uV
Audio Output Power: 1 Watt at 8Ω (less than 10% distortion)

Usage Features:

Power On/Off: The radio is powered on by turning the VOL knob clockwise and off by turning it anti-clockwise until a "Ka Ta" sound is heard.
Channel Selection: Channels can be increased or decreased using the CH or ACH keys. Holding these keys allows for fast channel changes.
Scan Function: A very long press of the CH or ACH key initiates the scan function, indicated by "SC" on the LCD. Scan direction can be changed with short presses of the CH or ACH keys, and scanning can be exited by pressing EMG or PTT.
External Speaker: The radio supports an 8Ω external speaker with a 3.5mm mono connector.
Microphone Jack: A dedicated jack is provided for connecting the microphone.
Power Connection: The radio requires a 12V DC power supply.
PTT Switch: The Push-to-Talk switch is used to initiate transmission.

Maintenance Features:

Antenna Installation: It is crucial to install the antenna and set the SWR (Standing Wave Ratio) before transmitting to prevent damage to the power amplifier. Failure to do so voids the warranty.
Factory Default Reset: The radio can be reset to factory default settings by holding the EMG key while powering on until "rt" is displayed on the LCD. This operation will restore all channel and function settings to their original state.
Power Cable Check: Users are advised to check the radio version (12V) before connecting the power cable to ensure it is supplied with a continuous current of 12 volts.

FCC Compliance and Safety:

The device complies with FCC rules, ensuring it does not cause harmful interference and accepts any received interference. Users are advised to maintain a minimum separation distance of 35.8cm for safe RF exposure. Modification of this device to receive cellular radiotelephone service signals is prohibited under FCC rules and federal law.

ABBREE AR-M6 Specifications

General

Brand	ABBREE
Model	AR-M6
Category	Radio
Language	English