Abus HomeTec Pro FCA3000 User Manual

31
General information
- Use the ABUS Home Tec Pro CFF3000 remote control / ABUS Home Tec Pro CFT3000 keypad (available
separately) for all menu items except 1
- Programming of the drive is carried out on two levels.
Level 1: Programming and clearing of remote control(s) and keypad, and factory reset.
Level 2: Advanced menu for setting signal tones, torque of the drive and activation of tilt function
-Alwaysscrollthroughamenuwithkeys1and2,cancelafunctionwithkey3andconrma
function with key 4.
-Everybuttonpressisconrmedbyasignaltone:asustainedtoneasaconrmation/acknowledge-
ment; a double tone as an erroneous or impermissible button press.
-Youcanndanoverviewoftheprogramstructureandtheassignmenttableunder7.,page47,52.
1. Level 1 - Programming the drive
-Aim:programmingofthedriveforyourwindowisrequiredoninitialcommissioningandaer
a factory reset
- Starting position: window handle is in “closed” position, but the cylinder must be unlocked
 -Presskeys1+2simultaneously,aerashorttimebothLEDsashyellow
 -Conrm“closed”positionbypressingkey4;alongsignaltonesounds
- Turn the handle to “open” position
 -Conrm“open”positionbypressingkey4;alongsignaltonesounds
- Turn the handle back to “closed” position. When the position is reached, a long signal
tone sounds
- The wireless window drive is now programmed for the window and the two LEDs go out
- Possible error message: if a position is not detected, instead of a long tone, a double tone sounds.
Movethewindowhandletothecorrectpositionandconrmitagain.
2. Level 1 - Programming of remote control(s) and keypad
- Aim: programming of transmitters so that you can operate the drive conveniently with the
remote control / keypad. You have the option to set up a maximum of 9 transmitters. If all memory
locationsareoccupied,youcanonlyopenthismenuitemaerdeletingmin.1transmitter.
- Starting position: the drive must have been programmed for the window (see menu 1)
 -Presskeys1+2simultaneously,aerashorttimeLED1turnsgreen
 -Conrmtheprogrammingprocessbypressingkey4;bothLEDsash.Indeliveredstate,
 therstfreememoryspaceisindicatedbythecolourcombinationgreen/green.
If transmitters have already been programmed, the next free memory space is displayed
 (colourcombinationgreen/yellow,thengreen/red,andsoon,seecongurationtable
>> 7., page 50).
 -Nowconrmtheremotecontrol/keypadtobeprogrammed(seeinstructionsCFF/CFT).
If programming is successful, a sustained tone sounds and the LEDs indicate the next free
memory space.
- To exit the menu item, press key 3.
3. Level 1 - Clearing remote control(s) and keypad
- Aim: you want to clear a programmed transmitter, e.g. because the remote control has been lost
 -Presskeys1+2simultaneously,aerashorttimeLED1turnsgreen
- Press key 2; LED1 turns yellow
 -Conrmyourintentiontoclearthetransmitterbypressingkey4
 -Therstassignedmemoryspaceisdisplayed(colourcombinationgreen/green).Ifmore
than one memory space has been assigned and you wish to clear one of them, switch to
the required space by pressing key 1 or 2

Abus HomeTec Pro FCA3000 Specifications

General

Model	FCA3000
Brand	Abus
Communication Protocol	Bluetooth
Communication	Wireless
Frequency	2.4 GHz
Power Source	Battery
Battery Type	4 x AA batteries
Type	Controller
Range	Up to 10 meters
Battery Life	Up to 1 year (depending on usage)
Operating Temperature	-10°C to +50°C