Acces 200700T User Manual

Ladder Components Qty
A) Handrails 2
B) Platform 1
C) Adjustable Support Feet 2
D) Outside Ladder Body 1
E) Ladder Foot Extension 1
G) Adjustable Support Tube 2
H) Support Tube Base 1
I) Ladder Secure Straps 2
Hardware Kit (not shown) Qty
J) 3/8” x 4” Carriage Bolt 4
K) 3/8” Hex Nut 4
L) 3/8” Flat Washer 4
M) #14 x 3/4” Tapping Screw 6
P) 1/4” x 2-1/4” Phillips Head Bolt 2
Q) 1/4” Acorn Nut 2
R) 1/4” Flat Washer 2
S) 1” Pan Head Screw 8
T) Lock Cable 1
SAFETY INSTRUCTIONS:
• Install ladder per manufacturer’s instructions.
• Locate ladder on a solid base.
• Ladder is designed for use by one person at a time.
• This ladder is intended for use as a swimming pool ladder only.
• Face ladder when entering and exiting the pool.
• No jumping, no diving from ladder.
• Do not swim through, behind or around the ladder or step system.
Model #200700T
SMART CHOICE LADDER
ASSEMBLY INSTRUCTIONS
STEP BY STEP ASSEMBLY INSTRUCTIONS
For use with Model # 200740T (Comfort Incline) / #200600T (Smart Step) / 200400T (Easy Entry Step)
Supplies Required: Phillips screwdriver or bit,
drill, 1/8” bit, tape measure, 7/16”and 9/16”
sockets, box or open end wrenches, padlock.
Note: Before you begin the assembly of your
ladder/step, please insure you have all components
and hardware.
Note: Contact our customer service department to
request any missing or damaged parts or hardware
at 888-333-1134.
Step 1 Platform and Handrail Assembly
Locate the Left and Right Handrail Assemblies (A) and the Platform (B). Secure the Handrail
Assemblies (A) to the Platform (B) by snapping them over the tabs on the platform.
Step 2 Adjustable Support Feet Preparation
Insert the Adjustable Support Feet (C) into the Handrail Assembly sockets as shown in the diagram.
DO NOT INSERT HARDWARE AT THIS TIME.
Step 3 Platform Support Tubes
Locate the Support Tube sockets on the underside of the Platform (B) and insert one end of each
Support Tube. Place the Support Tube Base (H) on the ground and insert other end of Adjustable
Support Tube (G) in Support Tube Base (H). DO NOT SECURE WITH HARDWARE AT THIS TIME.
continued on other side
A
B
C
D
E
G
H
Shown with Smart Step System
#200100T (200700T/200600T)
Shown with
Easy Entry System
#200800T
(200700T/200400T)
Shown with
Comfort Incline
(200700T/200740T)

Acces 200700T Specifications

General

Brand	Acces
Model	200700T
Category	Ladders
Language	English

Summary

Safety Instructions

Step-by-Step Assembly Instructions

Platform and Handrail Assembly

Secure the Handrail Assemblies (A) to the Platform (B) by snapping them over the tabs.

Adjustable Support Feet Preparation

Insert the Adjustable Support Feet (C) into the Handrail Assembly sockets without hardware.

Platform Support Tubes

Insert Support Tubes into platform and base sockets without securing with hardware.

Secure Support Feet or Incline

Secure the Adjustable Support Feet (C) or Comfort Incline (200740T) to the Handrail Assembly (A).

Cut to Fit Adjustable Parts

Cut Adjustable Support Feet (C) or Support Tubes (G) if needed for pool wall height.

Final Ladder Positioning and Securing

Position ladder, ensure platform is level, then secure feet/incline to handrail assembly.

Secure Assembly to Pool Top Rail

Use ladder secure straps to attach the platform to the pool top rail.

Secure Support Tubes with Hardware

Secure Adjustable Support Tubes (G) to platform and base using tapping screws.

Attach Outside Ladder Body

Secure the Ladder Foot Extension (E) to the Outside Ladder Body (D) using carriage bolts.

Lift-N-Lock Outside Ladder Operation

Swing up the Outside Ladder Body (D) for storage and secure with Lock Cable (T).