Series SR90
ITEM
CODE
SPECIFICATIONS
SERIES SR92-
INPUT
Multi input
CONTROL OUTPUT (1)
CONTROL OUTPUT (2)
(OPTION)
POWER SUPPLY
REMARKS
ANALOG OUTPUT (OPTION)
COMMUNICATION OR SV BIAS (OPTION)
EVENT OUTPUT/
HEATER BREAK ALARM (OPTION)
4
8
6
Y-
I-
P-
V-
Y-
N-
I-
P-
V-
90-
08-
0
1
2
3
0
9
MPU-Based Auto-Tuning PID Digital Controller, DIN H72 × W72 × D110mm
Thermocouple: B, R, S, K, E, J, T, N, PLII, Wre5-26 {U, L (DIN 43710)}
R.T.D.: Pt100Ω /JPt100Ω
Voltage (mV): -10~10, 0~10, 0~20,
0~50, 10~50, 0~100mV DC
Current (mA): 0~20, 4~20mA DC
Receiving impedance: 250Ω
Voltage (V): -1~1, 0~1, 0~2, 0~5, 1~5,
0~10V DC Input resistance: 500kΩ min.
Scaling Possible
For voltage and current input:
Range: -1999~9999
Span: 10~5000
Note: Inverse scaling
is not possible.
Contact: 1a, Contact capacity: 240V AC 2A/resistive load
Proportional cycle: 1~120 sec.
Current: 4~20mA DC
Load resistance: 600Ω max.
SSR drive voltage: 12V±1.5V DC/30mA max.
Proportional cycle: 1~120 sec.
Voltage: 0~10V DC
Load current: 2mA max.
Contact: 1a, Contact capacity: 240V AC 2A/resistive load
None
Proportional cycle: 1~120 sec.
Current: 4~20mA DC
Load resistance: 600Ω max. (RA when shipped)
SSR drive voltage: 12V±1.5V DC/30mA max.
Proportional cycle: 1~120 sec.
Voltage: 0~10V DC
Load current: 2mA max.
100V~240V AC±10%, 50/60Hz
24V AC/DC±10%, 50/60Hz
None
Event output (2a) Ev1, Ev2
Contact capacity: 240V AC 1A/resistive load
Event output (Ev1) + Heater break alarm (with CT30A)
Event output (Ev1) + Heater break alarm (with CT50A)
Voltage: 0~10mV DC, Output resistance: 10Ω
None
Voltage: 0~10V DC, Load current: 2mA max.
Current: 4~20mA DC, Load resistance: 300Ω max.
RS-485
None
1 point (setting range: -1999~5000), Non-voltage contact or Open collector input
RS-232C
when control output (1)
Note: Available only
is Y or P is selected.
With (Please consult before ordering.)
Open collector input rating: approx. 5V/1mA max.
Without
0
3
4
0
5
7
8
6
Note:
When you purchase a two-output type controller and use it in a one output capacity, larger overshooting or undershooting may happen as
a result of integral operation. Therefore, we recommend you to choose a one-output type.
The cause of the above-mentioned problem is that the positional relationship between the proportional band (PB) and the set value (SV)
of a one-output type controller differs from that of a two-output type.
Series SR90
ITEM
CODE
SPECIFICATIONS
SERIES
SR94-
SR93-
INPUT
Multi input
CONTROL OUTPUT (1)
POWER SUPPLY
REMARKS
OPTION
Analog output
Communication
Set value bias (S V bias)
EVENT OUTPUT/
HEATER BREAK ALARM (OPTION)
4
8
6
Y-
I-
P-
V-
Y-
I-
P-
V-
N-
08-
90-
0
1
2
3
00
08
38
68
Analog output +
Set value bias (S V bias)
48
30
40
60
05
0
9
MPU-Based Auto-Tuning PID Digital Controller, DIN H96 × W48 × D110mm
MPU-Based Auto-Tuning PID Digital Controller, DIN H96 × W96 × D110mm
Thermocouple: B, R, S, K, E, J, T, N, PLII, Wre5-26 {U, L (DIN 43710)}
R.T.D.: Pt100Ω /JPt100Ω
Voltage: -10~10, 0~10, 0~20,
0~50, 10~50, 0~100mV DC
Current (mA): 0~20, 4~20mA DC
Receiving impedance: 250Ω
Voltage (V): -1~1, 0~1, 0~2, 0~5, 0~10V DC
Load resistance: 600Ω max.
Scaling Possible
Range: -1999~9999
Span: 10~5000
Note: Inverse scaling
is not possible
Contact: 1a, Contact capacity: 240V AC 2A/resistive load
Proportional cycle: 1~120 sec.
Current: 4~20mA DC
Load resistance: 600Ω max.
SSR drive voltage: 12V±1.5V DC/30mA max.
Proportional cycle: 1~120 sec.
Voltage: 0~10V DC
Load current: 2mA max.
None
None
None
Current: 4~20mA DC, Load resistance: 300Ω max.
Voltage: 0~10mV DC, Output resistance: 10Ω
Voltage: 0~10mV DC, Output resistance: 10Ω
SV bias 1 point
Current: 4~20mA DC, Load resistance: 300Ω
max.
SV bias 1 point
Voltage: 0~10V DC, Load current: 2mA max.
SV bias 1 point
RS-485
07
RS-232C
Voltage: 0~10V DC, Load current: 2mA max.
Open collector input rating: approx. 5V/1mA max.
1 point (setting range: -1999~5000), Non-voltage contact or Open collector input
With (Please consult before ordering.)
Without
Contact: 1a, Contact capacity: 240V AC 2A/resistive load
Proportional cycle: 1~120 sec.
Current: 4~20mA DC
Load resistance: 600Ω max.
SSR drive voltage: 12V±1.5V DC/30mA max.
Proportional cycle: 1~120 sec.
Voltage: 0~10V DC
Load current: 2mA max.
100~240V AC±10%, 50/60Hz
24V AC/DC±10%, 50/60Hz
Event output (2a) Ev1, Ev2
Contact capacity: 240V AC 1A/resistive load
Event output (Ev1) + Heater break alarm (with CT30A)
Event output (Ev1) + Heater break alarm (with CT50A)
when control output (1)
Note: Available only
is Y or P is selected.
CONTROL OUTPUT (2)
(OPTION)
For voltage and current input:
Note:
When you purchase a two-output type controller and use it in a one output capacity, larger overshooting or undershooting may happen as
a result of integral operation. Therefore, we recommend you to choose a one-output type.
The cause of the above-mentioned problem is that the positional relationship between the proportional band (PB) and the set value (SV)
of a one-output type controller differs from that of a two-output type.
To Next Page
Loading...