FUNCTION SETTINGS
1. Press [ON/OFF] to turn on the scale, the display will show flash digits and
then --------, press [PRINT], the display will show b xxx BAU value (press
[UNIT] to select among 1200, 2400, 4800, 9600), our default setting is 9600.
Press [ZERO] to enter Parity mode, the display will show
P XXX PAR, press
[UNIT] to select odd,even,none (odd stands for 7 data bits with odd parity, even
stands for 7 data bits with even parity, none stands for 8 data bit without parity)our
default setting is none.
Press [ZERO] to enter Print mode, the display will show n xxx Mod, press [UNIT]
to select ON, OFF, KEY, STB (OFF stands for serial data output disabled, KEY
stands for demand mode by press
[PRINT], STB stands for automatic print when
scale is stable, ON stands for continuous print, our default setting is STB. Press
[ZERO] again to return to weighing mode.
2. Press [ON/OFF] to turn on the scale, the display will show flash digits and
then ----------, press [UNIT] to enter unit selecting function, the display will show
ON X (X stands for the units: g, oz, lb, dwt…tola...) press
[UNIT] to select ON
(activate the selected unit) or OFF (inactivate the selected unit), press [ZERO] again
to return to weighing mode.
3. Switch the power to “ON” and than press [ON/OFF] to turn on the scale。The
display shows F-E-9 to 0 and than “- - - - - - -”|，press [PCS] key to enter ZERO
track function setting，display shows ZRD x.xd，press [UNIT] key to select ZERO
track value（0.0d-0.5d-1.0d-1.5d-2.0d）; press[ZERO]key to enter ZERO track
function setting，display shows ZRT x.xd，press [UNIT] key to select ZERO track
time（05. to 4.0 seconds; press [ZERO] key to enter ZERO setting，display shows
RZD XXX, press [UNIT] key to select ZERO value（0.8d-1.8d-2.8d-3.8d）;press
[ZERO] key to enter FIL setting, press [UNIT] key to select filter range amend
(0-1-2-3-4-5-6-7),”2”is default setting; press [ZERO] key to select zero range when
turn on the scale, press [UNIT] key to select percent (PZR 2, PZR 5, PZR 10.
PZR 20); press [ZERO] key to set zero range, press [UNIT] key to select percent
(KZR 3,4,5,10); press [ZERO] key to set TARE range, press [UNIT] key select
percent (KTR 50 or KTR 100); press [ZERO] key to enter overload protection
setting, press [UNIT] key to select overload protection value (9d OVR-1 OVR-2
OVR-10 OVR); press [ZERO] key to set beep function, press [UNIT] key to choose
turn on or turn off the beep, “b2 ON” means activate the beep, “b2 OFF” means
inactivate the beep; press [ZERO] key to unite the function of TARE and ZREO,
press [UNIT] to switch between them. “ZT ON” means unite function activate,
“ZT OFF” means unite function inactivate. press [ZERO] key to enter auto off
function setting，display shows A xxx，press [UNIT] key to select auto off time
（3,5,10,off）. Press [ZERO] to select backlight, the display will show L Aut, press
[UNIT] to select X value (X stands for AUT, OFF, ON), OFF stands for inactivate
backlight function, ON stands for the backlight is always make function. AUTO
stands for auto backlight.
4. Press [ZERO] to return to weighing mode.
To Next Page
Need help?
General