Acumen Model L User Manual

Page 1 of 4
INSTALL BATTERIES INTO RECEIVER:
INSTALL BATTERIES INTO TRANSMITTER:
Replace Batteries At Least Every 6 Months.
WARNING: THE REMOTE TRANSMITTER WILL AUTOMATICALLY SWITCH OFF THE FIREPLACE
WHEN THE BATTERIES IN THE REMOTE TRANSMITTER ARE LOW.
RECEIVER OPERATION:
Fireplace Remote Control Operating Instructions For The Homeowner
The Model L Remote Control is designed for use with decorative gas fireplace and wall heaters using a
Millivolt gas valve.
BEFORE YOU BEGIN:
Warning The pilot flame must be lit, with the gas control valve turned to "ON", for the remote to work
correctly. Read all of the safety precautions in the owner's manual included with your
fireplace before using this remote control.The thermostat is not intended for unattended use.
INSTALLING FRESH BATTERIES:
Note: It is not necessary to re-set your private code when Installing Fresh Batteries.
The fireplace MUST be OFF before replacing transmitter batteries.
Acumen Model L
AA Alkaline Batteries.
Press and Release
PRESS
TO OPEN
PRESS
TO OPEN
FIREPLACE REMOTE
PRESS
TO OPEN
OFF
REMOTE
BAT.LOW
Fireplace Controlled
by Remote
Fireplace Off
Fireplace On
Low Battery
Indicator
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN
OFF REMOTE ON
BAT.LOW
PRESS TO OPEN

Acumen Model L Specifications

General

Battery Type	AAA
Battery Quantity	2
Operating Range	Up to 30 feet
Color	Black
Device Type	Remote Control
Material	Plastic

Summary

Before You Begin

Pilot Flame and Gas Valve Requirement

Ensures pilot flame is lit and gas valve is ON for correct remote operation. Read owner's manual for safety.

Thermostat Usage Warning

The thermostat is not intended for unattended use, emphasizing responsible operation.

Installing Fresh Batteries

Private Code Reset

No need to reset private code when installing fresh batteries.

Fireplace State for Battery Replacement

The fireplace MUST be OFF before replacing transmitter batteries.

Receiver Operation

Fireplace Off State

Illustrates the receiver state when the fireplace is off.

Fireplace Controlled by Remote State

Illustrates the receiver state when controlled by the remote.

Fireplace On State

Illustrates the receiver state when the fireplace is on.

Low Battery Indicator

Indicates the presence and function of the low battery indicator.

Transmitter Operation

Response Time Warning

Warning about receiver response time and button press frequency for correct operation.

Setting Clock and Temperature Mode

Step-by-step guide to setting the clock and choosing temperature display modes (°F/°C).

Auto Mode Functionality

Explains Auto mode as a thermostat, regulating heating based on desired temperature.

Automatic Receiver Shut-off Caution

Caution regarding automatic receiver shut-off after six hours of uninterrupted operation.

Manual Mode Operation

Describes how to manually turn the fireplace on/off and its limitations.

Timer Operation Setup

Instructions for setting the timer for fireplace operation duration.

Child-Proof Feature

Activating Child-Proof Mode

How to activate the Child-Proof switch and its effect on the LCD display.

Disabling Child-Proof Mode Temporarily

Sequence to temporarily restore button function and remove Child-Proof display.

Child-Proof Mode Re-engagement

Explains how the Child-Proof mode re-engages if no buttons are pressed for 2 minutes.

Set Private Code

Setting Code Switches

Procedure for setting code switches on transmitter and receiver for privacy.

Coding Instructions

Step-by-step guide to pair transmitter and receiver by setting a private code.

Important Safety Feature: 6HR Safety Timer

Enable 6HR Safety Timer

Enables automatic fireplace shutdown after 6 hours of no transmitter signal.

Disable 6HR Safety Timer

Disables automatic shutdown, allowing continuous operation.

FCC Requirements

Compliance and Interference Warning

Details compliance with FCC Part 15 rules and measures to correct interference.

Canadian Equipment Requirements

Compliance with Canadian Regulations

States compliance with Canadian Radio Interference Regulations and RSS-210.

Installation Instructions

Installation Precautions

Emphasizes safety, need for qualified technician, and adherence to manual for installation.

Installing the Receiver

Step-by-step guide for installing the remote receiver, including wiring and mounting.

Installing Receiver to Wall Mount

Instructions for securing the remote receiver to a wall mount using provided screws.

Installing Receiver to Fireplace

Steps for mounting the remote receiver to the fireplace base pan.

Important Safety Feature: Private Code

Coding Instructions

Detailed steps for setting a private code to prevent accidental operation by nearby transmitters.