Adel CBI2410A User Manual

A
A
D
D
E
E
L
L
s
s
y
y
s
s
t
t
e
e
m
m
Instruction Manual
ADEL system srl Via L. Barchi 9/B, 42100 Reggio Emilia (Italy) – Tel. ++39-0522-345518
Fax. ++39-0522-345551 – Internet: www.adelsystem.com
– e-mail: info@adelsystem.it
CBI2410A_R8 Eng.doc
CBI2410A – CBI2410A/S – CBI2410ARJ
Intelligent Battery Charger
Thank you for having chosen one of our products for your work. We are certain that it will give the utmost satisfaction and be a notable
help on the job.
General Description:
Application
CBI battery charger is a range of microprocessor-power supplies witch correctly charge sealed lead-acid batteries at all time
maximizing performance and life span.
Charge the battery in multi-stage principle, Fast and Trickle and automatically the device, check the battery efficiency in a lifetime to
prevent any risk of damage to the battery and allow leaving the charger permanently connected. Before begin the operations of
installation consult the manual.
Mains Characteristic
Nominal Input Voltage: 115 / 230 Vac
OUTPUT 1: for connection to Battery
OUTPUT 2: for connection to Load
Fast and trickle battery charge In according to DIN 41773
Signaling: replace battery, low battery, mains or buffering
Overload and short circuit protections
Safety isolation in according with EN 60950
Output 24 Vdc 10 A 50° C also without mains
Degree of protection IP20
Rail DIN mounting
Vac Input
Mains or
Backup
OUTPUT N°2
Load Vdc Output
Charging Level
OUTPUT N°1
Battery module
Low Battery or
Battery replacement
Battery Type
Configuration Jumper
Monitor Led
Bridge
Only 115Vac

Adel CBI2410A Specifications

General

Brand	Adel
Model	CBI2410A
Category	Battery Charger
Language	English

Summary

General Description

Application

Mains Characteristic

Use and Connections

Charging Level Current

Configures charging current from 20% to 100% of nominal capacity.

Connection to Battery module (Output 1)

Connects to battery, monitors charge status via LEDs.

Connection to Out Load (Output 2)

Provides 24 Vdc output for load connection.

Monitor Mains or Backup

Indicates mains or backup power status via LED and relay.

Monitor Low Battery or Battery replacement

Signals low battery or replacement need via LED and relay.

Life Test Battery

Performs battery efficiency checks every 4 hours in trickle charge.

Diagnosis Led

Provides diagnostic information through LED blinking patterns.

Cable connection

Details cable cross-sections and strip lengths for input/output.

Input Connection

Describes screw connections for mains input (L, N, PE).

Battery Type Configurations

Open Lead (Charge)

Sets charger for open lead-acid batteries, defining trickle/fast charge voltages.

Sealed Lead (Charge)

Configures charger for sealed lead-acid batteries, defining charge voltages.

Gel Battery (Charge)

Sets charger for gel batteries, defining trickle/fast charge voltages.

Life Test Battery

Configures for battery life testing mode.

No jumper no Fast Charge

Disables fast charge when position 5 jumper is absent.

Compensation Recharges in temperature

Protection

Primary side protection

Mentions internal fuse T 6 A/250Vac for primary side protection.

Secondary side protection

Details electrical protection against short circuits and overload.

Inversion polarity protection

Module is protected against battery polarity inversion.

Over current and output short circuit

Limits output current to max 12A and reduces voltage on overload.

Deep discharge protection

Prevents deep discharge by disconnecting the battery at minimum voltage.

Battery Test

Automatically checks battery polarity and efficiency every 4 hours.

Characteristic Curves

Short circuit and overload

Output is protected against overload and short circuit, reducing voltage with increasing overload.

Thermal behavior

Device supplies nominal current up to 50°C, then reduces output by 1% per °C.

Standards and Certification

Electrical safety

Installation must comply with EN60950, requiring external isolating facility.

General Standard

Immunity according to EN50082-2 Level 4 Class B, radio interference suppression EN55011 Class A.

Features

Input Data

Specifications for nominal input voltage, range, inrush current, frequency, and input current.

Output Data

Specifications for output voltage, current, adjustment, backup mode, and protections.

Climatic Data

Operational and storage temperature ranges, and humidity limits.

General Data

Includes isolation voltage, ground insulation, electrical safety, protection class, dimensions, and weight.