To Next PageTo Next Page
Need help?Do you have a question about the ADJ HD MB40KG and is the answer not in the manual?
Warning about potential electric shock from dangerous voltage when touching wires.
Emphasizes following safety instructions and warning notes for safe operation.
Advice on handling devices exposed to drastic temperature changes to prevent condensation damage.
Electrical connections must only be performed by a qualified electrician.
Instructions on handling the power cord and connections to avoid contact with other cables.
Specifies the maximum weight limit for the mirror ball motor is 89 lbs.
Clarifies that the product is designed exclusively for indoor usage.
Requirement to keep the area below the fixture clear during rigging, derigging, or servicing.
Recommends saving and using original packaging for product transportation.
Warns that operating the motor differently than described voids warranty and causes dangers.
Advises to consider EN 60598 norms during the installation process.
States that installation must be performed by a qualified electrician or authorized dealer.
Mandates installation structure to hold 5x weight for 1 hour without deformation.
Requirement for a secondary safety attachment, like a safety cable, to prevent falling.
Prohibits rigging or servicing over high working places or public areas.
Ensures safety and technical installations are approved by an expert.
Recommends installing the motor in a strictly horizontal position.
Motor and mirror ball must be installed out of reach and not swing freely.
Ensures installation structure can hold a minimum of 400lbs point load before rigging.
Instructions on using all 10 fixation holes and appropriate screws for connection.
Requirement for a disconnection switch for direct power supply network connection.
Recommends using chains certified for mirror balls up to specified sizes.
Warns against using abrading material like steel cables for chains to prevent wear.
Specifies that the length of the chain must not exceed 100 cm.
Ensures the chain is inserted and the fixation screw is tightened properly.
Verify that the mirror ball rotation is not slowed down or obstructed.
Check key rings or chain links for deformation/damage and remove if found.
Recommend frequent cleaning with a soft, lint-free, moistened cloth; avoid alcohol/solvents.
States there are no user-serviceable parts; maintenance must be by authorized dealers.
Advise to use only genuine parts for any required replacements.
Power supply cable damage requires replacement by authorized dealers only.
User-serviceable parts are not present; contact ADJ Products, LLC for failures.
Provides toll-free support line, website, voice, fax, and email for assistance.
The HD MB40KG has a 1-year limited warranty; fill out card to validate purchase.
All returned items must be freight pre-paid and accompanied by a return authorization (R.A.) number.
Warrants products against defects for a prescribed period, valid only in the USA.
Obtain RA#, contact factory, pay pre-paid shipping; ADJ pays return shipping within the USA.
Warranty void if serial number altered, product modified, or repaired by unauthorized personnel.
Warranty does not include maintenance, cleaning, or periodic check-ups; covers repair/replacement.
ADJ Products, LLC reserves the right to make design changes without obligation to prior products.
No warranty is given for accessories; implied warranties limited to the product's warranty period.
Lists limited warranty periods for different product types, including lighting and LED products.
Warning about potential electric shock from dangerous voltage when touching wires.
Emphasizes following safety instructions and warning notes for safe operation.
Advice on handling devices exposed to drastic temperature changes to prevent condensation damage.
Electrical connections must only be performed by a qualified electrician.
Instructions on handling the power cord and connections to avoid contact with other cables.
Specifies the maximum weight limit for the mirror ball motor is 89 lbs.
Clarifies that the product is designed exclusively for indoor usage.
Requirement to keep the area below the fixture clear during rigging, derigging, or servicing.
Recommends saving and using original packaging for product transportation.
Warns that operating the motor differently than described voids warranty and causes dangers.
Advises to consider EN 60598 norms during the installation process.
States that installation must be performed by a qualified electrician or authorized dealer.
Mandates installation structure to hold 5x weight for 1 hour without deformation.
Requirement for a secondary safety attachment, like a safety cable, to prevent falling.
Prohibits rigging or servicing over high working places or public areas.
Ensures safety and technical installations are approved by an expert.
Recommends installing the motor in a strictly horizontal position.
Motor and mirror ball must be installed out of reach and not swing freely.
Ensures installation structure can hold a minimum of 400lbs point load before rigging.
Instructions on using all 10 fixation holes and appropriate screws for connection.
Requirement for a disconnection switch for direct power supply network connection.
Recommends using chains certified for mirror balls up to specified sizes.
Warns against using abrading material like steel cables for chains to prevent wear.
Specifies that the length of the chain must not exceed 100 cm.
Ensures the chain is inserted and the fixation screw is tightened properly.
Verify that the mirror ball rotation is not slowed down or obstructed.
Check key rings or chain links for deformation/damage and remove if found.
Recommend frequent cleaning with a soft, lint-free, moistened cloth; avoid alcohol/solvents.
States there are no user-serviceable parts; maintenance must be by authorized dealers.
Advise to use only genuine parts for any required replacements.
Power supply cable damage requires replacement by authorized dealers only.
User-serviceable parts are not present; contact ADJ Products, LLC for failures.
Provides toll-free support line, website, voice, fax, and email for assistance.
The HD MB40KG has a 1-year limited warranty; fill out card to validate purchase.
All returned items must be freight pre-paid and accompanied by a return authorization (R.A.) number.
Warrants products against defects for a prescribed period, valid only in the USA.
Obtain RA#, contact factory, pay pre-paid shipping; ADJ pays return shipping within the USA.
Warranty void if serial number altered, product modified, or repaired by unauthorized personnel.
Warranty does not include maintenance, cleaning, or periodic check-ups; covers repair/replacement.
ADJ Products, LLC reserves the right to make design changes without obligation to prior products.
No warranty is given for accessories; implied warranties limited to the product's warranty period.
Lists limited warranty periods for different product types, including lighting and LED products.
General