EasyManua.ls Logo

ADO A20 - Maintenance and Repair; Daily Maintenance Routine; Lubrication Schedule; Motor, Controller, and Battery Care

ADO A20
17 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
11
Maintenance and Repair
Daily maintenance:
1.The vehicle should be kept clean and clean, and the vehicle should be wiped with dry cloth in
time after being drenched to avoid rusting of parts and short circuit of electrical components.
2.Always check the air storage capacity of the tire to keep it in normal use.
3.The main transmission parts such as front axle, a roar axle, conter axle, front fork, Flywheel and
electric hub should be checked and adjusted frequently to keep the transmission parts flexible
without impact sound and noise; Check the screws and nuts of the whole car, if it is found that it is
loose, it should be tightened in time to prevent the parts from being worn out or causing greater
damage and fracture due to looseness.
4.The braking part should be checked and adjusted frequently to make it in a flexible state, for
example, the gap between the brake rubber and the gate core should not be too large.
5.Always check whether the operating parts and cable are flexible, and ensure that there is no
stagnation, no stagnation, and properly drip lubricating oil from one end of the hose slowly, and
pull the wire rope at the same time, feel that the wire rope slides lightly in the hose.
6.Electric bicycle moving parts should be often injected with a small amount of lubricating oil to
reduce wear and keep riding light, as shown in the following table:
Correct use and maintenance methods of motor, controller and battery:
1.The motor should be kept clean, no foreign matter, corrosive liquid, gas, etc. should enter the
motor, and the motor Shell should not be knocked and baked to avoid damage to the motor.
2. All wires should avoid friction and contact with sharp metal, and the wires should be tied firmly
with the frame.
3.The controller is a high-tech intelligent computer memory program password. If the user opens
the repair by himself, the components will be easily damaged. If the controller fails, please go to
the service department to repair it.
4.This battery is a special battery for electric bicycles. When the electric bicycle is not used for a
long time, the battery should be stored after sufficient electricity, and the electric energy should be
replenished regularly to avoid battery vulcanization caused by long-term under power.
5.The battery cannot be near open flame or high temperature heat source, and the battery cannot
be thrown into the fire. Direct exposure to the sun is strictly prohibited in hot and hot weather.
Note that the tightening torque of front wheel, handlebar core screw rod, saddle pipe
clamping Bolt and saddle clamping Bolt shall not be less than18N.m;The tightening torque of
rear wheel, bottom bracket Cup and bottom bracket Cup lock nut shall not be less than
30N.m
Front axle, center axle, a rear
axle bearing
3# calcium-based lubricating oil
Six months to one year
Half a year
Half a year
Half a month
Half a month
3# calcium-based lubricating oil
3 pieces of calcium-base
lubricating oil
30# mechanical oil
30 and mechanical oil
front fork headset
Pedal bearing
Chain
Double support locking plate side
support and transmission parts
Name
Handle
horizontal tube
stem Saddle Saddle pipe front axle rear axle Center shaft nut
Running torque 18N. m 18N. m 18N. m 18N. m 18N. m 30N. m 30N. m
Lubrication part Lubricant Lubrication cycle
Location Method Time
Center shaft
Front and
rear wheels
brake cable
brake handle
Chain
Front and rear nut, handlebar
core screw, saddle clamping screw
Check whether the bottom bracket Cup is loose/disassemble
the central shaft, wash and change oil, and check the parts.
Check the wheel swing, spoke tension, spokes, mother spoke
for damage; Adjust the wheel
If there is a steel wire at the root of the rolling head,
replace the new brake line.
If there is a steel wire at the root of the rolling head,
replace the new brake line.
Check whether the pin shaft is loose or bulging, and
whether the extension of the chain is too large.
Check for looseness
Check frequently /once every year
The first month/year after the
first new car
Once every month
Once every three months
Once every six months
Once every six months

Other manuals for ADO A20