AEG BSS 4802 - First Use and Introduction; Power Supply and Connection; Setting the Clock; Radio Mode Operations

English
34
First Use of the Device/Introduction
NOTE:
The buttons on the device are touch buttons. Touch the
keys lightly with a finger to perform the function.
• Selectaproperplaceforthedevice.Adry,levelandslip
proof surface is suitable.
• Makesurethedeviceisventedsufciently!
• Removetheprotectivelmfromthedevice,ifpresent.
Power supply
• Insertthegridplugintoaproperlyinstalledthreeprong
socket with 230 V, 50 Hz. Connect the device with the
plug connector by inserting its plug into the DC 12 V jack
of the device.
• Makesurethegridvoltagecorrespondstothegureson
the rating plate.
CAUTION:
• TheincludedACadaptermayonlybeusedwiththis
device. Do not use it for other devices.
• UseonlyanACadapterwith12V(
). A different
AC adapter may damage the unit.
NOTE:
• Disconnectfrommainspowersupplyduringlonger
periods of non-use.
• Thetimeandthestoredradiostationsarelostassoon
as the power supply has been interrupted.
Setting the clock (during standby mode)
1. Briefly hold down the TIME/MEM button (10). The hour
indicator starts to flash.
2. Use UP/DN buttons to set the hours. Confirm with TIME/
MEM.
3. Use UP/DN buttons to set the minutes.
4. Press TIME/MEM again in order to save the time settings.
NOTE:
Ifnothingisenteredwithinapprox.6seconds,thedevice
reverts back to the normal display.
General Operation
Switch device on/off
• WiththeSTANDBYbutton(9),youcanswitchtheunit
between standby and operating mode. The time is
displayed in standby mode.
• Todisconnecttheunitcompletelyfromthemains,pull
the mains plug from the socket.
NOTE:
• Thetimeandthestoredradiostationsarelostassoon
as the power supply has been interrupted.
NOTE:
• After10minuteswithoutasignal,thedeviceswitches
to standby automatically.
Volume
By pressing the VOL+/VOL- buttons (5) you can adjust the
desired volume.
Sound Settings
If necessary, change the EQ setting in your playback unit to
create the best sound.
Display brightness
When the display is in standby, you can set the brightness of
the display by repeatedly pressing the SLEEP button (11).
Radio mode
Search for a radio station
1. Fully uncoil the wire antenna.
2. You have two options in order to search for a radio sta-
tion:
• AdjustthedesiredradiostationusingtheUPorDN
button (14).
• KeeptheUPorDNbuttonpresseddownforashort
while.Thedevicewillstopatthenextradiostation.
3. If the reception is too weak and there is interference on
the received station, try to improve the reception by alter-
ing the position and uncoiling or coiling the antenna.
Storing radio stations
1. Search for a radio station as described under “Search for
a radio station”.
2. Press the TIME/MEM button (10). The display will start to
flash.
3. Using the UP/DN buttons (14) select the memory location
where the radio station is to be stored.
4. Press the TIME/MEM button again. The radio station will
be stored and the display will stop flashing.
NOTE:
The stored radio stations are lost as soon as the power sup-
ply has been interrupted.
Select the preset radio station
You can select the stored radio sender with the ALARM/M+
and M- buttons (7/6).
Playing back music files
You have three options to play back your own music files with
the unit: hardwired, wireless via Bluetooth, or via the USB
port.