AERMEC FCW Series - Specific Operating Modes; Dehumidification and Sleep Modes

40
English
1508 - 5138800_00
The programme requires the system to circulate chilled water.
ϭΉWZ^^d,KEK&&
OR dhZEKEt/d, OR <z^
The fan coil comes on and the display is switched on.
ϮΉWZ^^d,<zDK
OR
Press the MODE key repeatedly until the word DRY appears on the display (TLW2) or
the LEDs on wired control panel (PFW2) turns on DRY.
ϯΉWZ^^d,<z^
OR dKKEdZK>d,dDWZdhZ
– The key with the symbol
allows increases of 1°C
– The key with the symbol
allows decreases of 1°C
The display shows the set point value between 16 and 30 °C.
ϰΉdK/Zdd,/Z&>Kt
To ensure optimum air distribution, adjust the horizontal blades and the vertical
blades in such a way that the air flow does not hit people directly. The vertical air flow
blades must be set manually before starting up the motorised blades.
Never adjust the motorised horizontal blades manually.
When the LOUVER key is pressed repeatedly, the horizontal blade is adjusted to 4 fixed
blade positions, then a swinging blade movement will begin. If you wish to stop the
blade in a particular position, press the LOUVER key.
When the SWING key is pressed a swinging blade movement will begin. If you wish to
stop the blade in a particular position, press the SWING key again.
ϱΉWZ^^d,^E<zΈd>tϮΉ
To transmit the new parameters shown on the LCD to the main control unit.
dŚĞĨĂŶĐŽŝůƵŶŝƚǁŝůůĂůǁĂLJƐŽƉĞƌĂƚĞĂƚŵŝŶŝŵƵŵƐƉĞĞĚ
PFW2
TLW2
Tset + 3°C
Tset + 2°C
Tset + 1°C
Tset °C
Tset - 3°C
Tset - 2°C
Tset - 1°C
Tset °C
0 30’ 1h 2h h
0 30’ 1h 2h h
“SLEEP”
with operation in cooling mode (COOL)
“SLEEP”
with operation in heating mode (HEAT)
6
PFW2
TLW2
The SLEEP programme operates regardless of the time of day.
Normally it is used during the night time hours.
ϭΉWZ^^d,KEK&&
OR dhZEKEt/d, OR <z^
The fan coil unit comes on and display is switched on.
ϮΉWZ^^d,DK<z
This can only be activated with AUTO, HEAT and COOL programmed.
ϯΉWZ^^d,<z^
OR dKKEdZK>d,dDWZdhZ
– The key with the symbol
allows increases of 1°C
– The key with the symbol
allows decreases of 1°C
The display shows the set point value between 16 and 30 °C.
ϰΉWZ^^d,&E<z
OR
When the FAN key is pressed repeatedly, the system can move to the minimum speed
(LOW), medium speed (MED) and high speed (HIGH) or to the (AUTO) speed controlled
by the microprocessor.
ϱΉWZ^^d,^>W<z
ϲΉWZ^^d,^E<zΈd>tϮΉ
To transmit the new parameters shown on the LCD to the main control unit.
t,d,WWE^t,Ed,E/',dKD&KZd&hEd/KE^>WWZK'ZDD/^^d
The temperature set point is automatically adjusted to ensure comfortable conditions
whilst saving energy.
E/',dKD&KZd&hEd/KEΈ^>WΉ
,hD//&/d/KEWZK'ZDDΈZzΉ