To Next PageTo Next Page
Need help?Do you have a question about the AES GSM-5AS/3GE and is the answer not in the manual?
General| Brand | AES |
|---|---|
| Model | GSM-5AS/3GE |
| Category | Intercom System |
| Language | English |
Assesses GSM cell coverage at the installation site.
Details the necessary specifications for the SIM card.
Specifies correct cable types and gauge for powering the unit.
Mounting instructions for architectural intercom panels.
Mounting instructions for hooded intercom panels.
Mounting instructions for flush intercom panels.
Step-by-step guide for inserting the micro-SIM card.
Details wiring connections for the GSM controller and its components.
Illustrates relay connections for gates and locks.
Procedure for powering on the intercom system.
How to check the GSM signal strength using an SMS command.
Configures phone numbers to be dialled when the call button is pressed.
Details programming dial-out numbers for specific buttons on multi-button panels.
Adjusts the duration the unit attempts to call a number.
Allows specific numbers to trigger outputs without answering.
Sets and calibrates the intercom's internal time clock.
Configures automatic time shifts for daylight saving.
Restricts button activation to specific times and days.
Sets an alternative number to call after specific hours.
Sets up permanent access codes for relay activation.
Sets up temporary access codes that expire after a set duration.
Sets up access codes valid only during specific times/days.
Procedures for deleting single or all keypad codes.
Configures automatic gate opening/closing at set times.
Clears all programmed automatic triggering events.
Configures a master number for SMS notifications on relay activation.
Details commands for changing programming and access control passwords.
Parameters for storing and deleting dial-out numbers.
Parameters for adjusting speaker and microphone volume.
Sets up scheduled calls or SMS to a service number.
Manages storing and deleting caller ID numbers.
Disables latching relays via DTMF tones.
Commands for checking reception, stored numbers, and status.
Resets all programming to factory defaults.
Describes the sequence of calls to up to four numbers.
How to open gates using a recognized stored phone number.
How to open gates using an unknown number with a passcode.
Steps to set up the CellcomPRIME app on Android devices.
Steps to set up the CellcomPRIME app on iPhone devices.
Triggering gates via the app's 'Open Gates' function.
Releasing latched relays via the app.
Accessing keypad code management within the app.
Holding relays in an open state via the app.
Configuring SMS notifications for triggered events via the app.
Accessing app features like auto-triggering and activity log.
Setting days and times for restricted button access in the app.
Configuring an alternate call number for after-hours operation in the app.
Setting scheduled times for automatic gate operations via the app.
Accessing signal strength, stored numbers, gate status, and activity log.
Interface for setting time-restricted keypad codes in the app.
Interface for setting permanent keypad access codes in the app.
Interface for setting temporary keypad access codes in the app.
Interface for deleting saved keypad codes in the app.
Triggering gates via the iPhone app's 'Open Gates' function.
Releasing latched relays via the iPhone app.
Accessing keypad code management within the iPhone app.
Holding relays in an open state via the iPhone app.
Configuring SMS notifications for triggered events via the iPhone app.
Accessing app features like auto-triggering and activity log on iPhone.
Setting days and times for restricted button access in the app.
Configuring an alternate call number for after-hours operation in the app.
Setting scheduled times for automatic gate operations via the app.
Accessing signal strength, stored numbers, gate status, and activity log on iPhone.
Interface for setting time-restricted keypad codes in the app.
Interface for setting permanent keypad access codes in the app.
Interface for setting temporary keypad access codes in the app.
Interface for deleting saved keypad codes in the app.
Commands to control relays and check system status via SMS.
SMS command to check the status of input limit switches and relays.
SMS command to retrieve a log of the last 20 events.
Guidance on keeping the intercom clean and functional.
Resolving problems with unit power, network reception, and SMS response.
Addressing issues with call timing, voicemail, and Caller ID functionality.
Diagnosing audio problems where the gate-side user has no audio.
Diagnosing and fixing poor audio quality or humming issues.
Resolving issues where keypad codes don't open gates or relays fail.
Diagnosing why the unit fails to make outgoing calls.
Records of changes and updates to the product versions.
Details the radio functions and frequency bands used by the device.
Statement of compliance with essential requirements and RED 2014/53/EU.
Compliance information regarding FCC rules for digital devices.
Information on FCC radiation exposure limits and operating conditions.
