Air Hogs Zero Gravity Laser User Manual

Zero Gravity Laser
™
Wall Racer
Controller/Charger
NOTE: USE ON SMOOTH, CLEAN
SURFACES ONLY!
FOR INDOOR USE ONLY.
ADULT SUPERVISION RECOMMENDED!
TO GET THE MOST OUT OF YOUR
ZERO GRAVITY LASER™
WALL RACER PLEASE READ THESE
INSTRUCTIONS FIRST!
Check to make sure contents are
complete:
• 1 Zero Gravity Laser™ Wall Racer
• 1 Controller/Charger
• 1 Instruction Guide
BATTERY INSTALLATION
CHARGING YOUR ZERO GRAVITY LASER™
1. Switch
car to “OFF”.
2. Switch
controller/
charger to
“OFF”.
3. Take out
charger
plug and
plug into
c a r.
4. Slide the
switch to
the “Charge”
position on
the controller.
5. Red light ashing:
Vehicle is charging.
Green & Red light
ashing together:
Vehicle is charged.
Green & Red light ashing
alternatively: error.
Green light
ashing/Red light off:
Replace AA Batteries.
6. When
charged, turn
controller/
charger
switch to
“OFF”.
• Charging should take between 30 and 50 minutes depending on how much charge is left in the car.
• NOTE: Do not charge battery immediately after use. Let the car battery cool for at least 10 minutes.
If charging is not complete in 50 minutes, replace the charger batteries.
Your Wall Climber has a pre-installed rechargeable battery inside the vehicle body. (Rechargeable battery is not replaceable.)
CONTROLLER/CHARGER
Six 1.5-V AA
Alkaline Batteries
Battery
Compartment
Battery
Compartment
Door
OF F
CHARGE OFF ON
CHARGE OFF ON
CHARGE OFF ON
Red
LED
Green
LED
TM
1. Requires 6 1.5-V AA alkaline batteries.
2. Open the battery door with a screwdriver.
3. If used batteries are present, remove these batteries from the
unit by pulling up on one end of each battery.
4. Install new batteries as shown in the polarity diagram (+/-) inside
the battery compartment.
5. Replace battery door securely.
6. Check your local laws and regulations for correct recycling and/or
battery disposal.
INSTRUCTION
GUIDE
®
1

Air Hogs Zero Gravity Laser Specifications

General

Control	Remote Control
Age Recommendation	8 years and up
Material	Plastic
Surface Compatibility	Walls, Floors
Battery Type	Lithium Polymer
Special Feature	Laser Guided
Color	Red
Type	Wall Climbing Car
Remote Battery	3 x AAA batteries (not included)

Summary

Battery Installation

Controller/Charger Battery Installation

Install 6 x 1.5-V AA batteries into the controller/charger compartment, observing polarity diagrams.

Charging Your Zero Gravity Laser™

Charging Procedure and Indicators

Steps for charging the vehicle's internal battery, including LED status lights for charging, charged, and errors.

Driving Modes and Operation

Driving on Walls or Upside Down

Setting the vehicle switch to the left for wall climbing and upside-down driving.

Driving on the Ground

Setting the vehicle switch to the middle for ground driving, saving battery charge.

Driving Sequence

How to use the controller's beam to guide the vehicle on walls or ground.

Driving Rules and Precautions

Operational Distance and Beam Radius

Maintain distance within 2m/6ft and point laser beam within 0.33m/1ft radius of the vehicle.

Surface Requirements

Drive only on smooth, clean, dry surfaces and avoid uneven or porous surfaces.

Prohibited Surfaces

Avoid driving off corners, edges, or on windows/glass/reflective surfaces.

Troubleshooting and Safety

Troubleshooting Common Problems

Solutions for vehicle not running, not climbing, or slipping/falling off walls.

Battery Safety Information

Guidelines for using and handling AA and Lithium Polymer batteries, including warnings.

General Safety Warnings

Includes laser light warnings, adult supervision, product care, and FCC compliance.