airmaster AM 50 - Mounting Manual

To Next Page

Mounting

AM 50

1·2

Main Page

Table of Contents3
Introduction6
Target Group6
Warning Symbols6
Liability6
Safety Instructions7
Responsibility7
Personnel Requirements7
Product Identification8
Product Name and Type8
Correct Use8
Capacity8
Specifications8
Wall Thickness8
Table 1 - Product Name and Type8
Table 2 - Capacity, Sound Pressure, Nominal Current8
Dimensions9
Filter Class9
Manufacturer9
Figure 1 - Minimum Wall Thickness9
Figure 2 - Dimensions. All Measurements in [MM]9
EU Declaration of Conformity10
Certificates10
Warranty10
Transportation and Storage11
Table 3 - Weight and Dimensions11
Installation12
Installation Accessories and Tools12
Unpacking12
Figure 3 - Unpacking12
Minimum Distance to the Building Parts13
Mutual Minimum Distances13
Figure 4 - Minimum Distances to the Building Parts (in MM)13
Figure 5 - Mutual Minimum Distances13
Hole Drilling14
Shortening the Tubes14
Figure 6 - Drilling the Hole in the Wall14
Figure 7 - Wall Thickness for Calculating the Tube Length14
Ø250 MM15
Ø90 MM15
Isolation15
Figure 8 - Shortening of the Ø250 MM Tube15
Figure 9 - Shortening of the Ø90 MM Tube15
Outside Mounting16
Preparation of Outside Hood16
Figure 10 - Preparation of Outside Hood with Ø90 MM Tube16
Figure 11 - Preparation of Outside Hood with Ø250 MM Tube16
Mounting of Sealing Band on the Outside Hood17
Sealing Tape on Façade Wall17
Figure 12 - Sealing Band on the Outside Hood17
Figure 13 - Outside Sealing Tape17
Applying Sealant between Sealing Tape and Façade Wall18
Mounting of the Outside Hood18
Figure 14 - Outside Sealant Application18
Figure 15 - Mounting of the Outside Hood18
Figure 16 - Outside Hood, Level19
Internal Mounting20
Applying Sealant20
Preparing the Wall Cover20
Figure 17 - Internal Sealant20
Mounting the Wall Cover21
Figure 18 - Application of Elastic Sealant to the Wall Cover21
Figure 19 - Mounting of Internal Wall Cover21
Fixation and Tensioning22
Figure 20 - Strips from the Outside Hood Are Guided into the Internal Wall Cover23
Figure 21 - One Loose Strip Is Connected to each of the Strips23
Figure 22 - the Strips Are Pushed down23
Figure 23 - Bend and Cut the "Mounted" Strips23
Figure 24 - Bend and Cut the Other Strips23
Figure 25 -The Internal Wall Cover Is Assembled23
Electrical Connection24
Cable Connection and Wiring24
Figure 26 - 24V Cable Routing24
Figure 27 - 24V Cable Connection to Terminal 124
Figure 28 - Sealing Cable Hole25
Figure 29 - 230V Cable Connecting; Several Options Available25
230V Cable Connection, Top (Standard)26
Figure 30 - Terminal 226
Figure 31 - 230V Cable Connection in Terminal 226
230V Cable Connection from the Right or Bottom27
Figure 32 - New Location of Terminal 2 if Cable Connection to the Right Is Required27
Figure 33 - Shorten the Internal Cable27
Figure 34 - Internal Cable Connected to Terminal 227
Figure 35 - 230V Cable Connection from the Right with Cable Clamp28
Figure 36 - Location of Terminal 2 with Cable Routing from below28
230V Cable Connection from the Left29
Figure 37 - Remove the Internal Cable29
Figure 38 - Connecting the Left Side Cable and Wiring29
230V Hidden Cable Connection30
Figure 39 - Cable Connection with Cable Clamp in Terminal 330
Figure 40 - Hidden 230V Cable Connection30
Mounting the Air Handling Unit31
Half-Hole for Cable (Only for Visible Cable Routing)31
Mounting and Fixation of the Ventilation Unit31
Figure 41 - Half-Hole for the 230V Cable, Shown here with a Connection from the Top31
Figure 42 - the Ventilation Unit Mounted in the Tube31
Mounting the Internal Cover32
Figure 43 - the Ventilation Unit Is Clicked Unto the Wall Cover32
Figure 44 - the Internal Cover Is Mounted on the Ventilation Unit32
Testing the Installation33
Figure 45 - Starting am 50 (Testing the Installation)33
Dismounting, Disassembly and Disposal34
Dismounting34
Disassembly34
Disposal34
Appendix Aeu Declaration of Conformity35
Appendix B Certificates36

airmaster AM 50 - Mounting Manual

Table of Contents

Other manuals for airmaster AM 50

Related product manuals