Features and content
1 Power indicator
2 Light ring
3 Wave sensor
4 Air inlets
5 Battery compartments
6 Battery tab
7 Mounting bracket
8 Screw and plug
9 2x AA batteries (inserted)
1
7 8 9
2 3 4 65
No response from light ring
- Make sure no objects have been obstructing the wave sensor.
Wait 30 minutes and retry.
- If the power indicator is blinking red, the battery level is too low for
the light ring to work. Replace batteries according to specications.
Not able to connect to “my device”
- Make sure you have the detector within range.
Bluetooth range is 10-15 meters / 30-50 feet.
- Check if Bluetooth is turned on.
- Check if the power indicator is blinking.
To snooze the high radon level alert:
- Follow directions in app.
- Wave in front of the detector.
My app is not updated when running in background mode. Make sure:
- open the app manager and verify the app is open and running in
the background.
- you are within Bluetooth range periodically.
Troubleshooting
The Airthings Wave is intended for indoor
use only. Avoid direct exposure to sunlight
for long periods. Avoid exposure to direct
heat sources. For a correct use, make sure
the detector is operating in the specied
temperature range (see technical speci-
cations).
Exposure to high humidity might per-
manently alter the detector sensitivity, or
damage it.
Do not disassemble. If the detector does
not work as specied or you are in doubt,
contact your local dealer or visit us at
airthings.com.
Use a dry cloth to clean the detector.
When replacing batteries, pay attention to
the polarity marks. Use AA alkaline (LR6)
batteries or Energizer L91 (Li-FeS2O) for
longer battery life (as supplied). Do not use
other Lithium batteries or chemistries than
those specied above.
Disposal: caution shall be used when han-
dling Lithium batteries. Lithium batteries
might explode if mechanically damaged
or overheated.
Always snap the mounting bracket to the
detector’s rear side to protect the batter-
ies, even when the detector is not perma-
nently mounted.
Safety
Technical Specications
For other languages or any other question go to: support.airthings.com
The Bluetooth® word mark and logos are registered trademarks owned by
the Bluetooth SIG, Inc. and any use of such marks by Airthings is under license.
Copyright Airthings AS
The instrument is tested and quality-as-
sured by production. It meets the accuracy
values set out in the specications.
It is recommended to keep the instrument
constantly activated and the batteries in
place until drained.
Airthings AS shall not be liable for damages
related to failure or loss of data arising from
incorrect operations and handling of the
instrument.
Terms & Conditions:
airthings.com/terms-use-privacy/
Limited liability
Power supply: 2x AA alkaline (LR6) or Energizer L91 batteries
Dimensions: Radius: 120 mm (4.72 in)
Height: 36 mm (1.42 in)
Weight: 219 g (incl. 2x E91 batteries)
Operational and storage environment:
Temperature: +4 °C (39 °F) to +40 °C (104 °F)
Relative humidity: < 85 %
Initial Accuracy/Precision at 100 Bq/m
3
(2.7 pCi/L):
7 days < 20 %
1 month < 10 %
Measurement range: 0 Bq/m3 to 50000 Bq/m
3
(0 pCi/L to 1350 pCi/L)
Parkveien 53b, NO-0256 Oslo
Norway
www.airthings.com
1-MAN-2900-B
Welcome1
7
8
9
10
2
Please read the manual carefully before using the product
Power indicator:
Flashing dot every 20 seconds.
Green: Battery level is ok.
Blue: Bluetooth connection
active.
Red: Replace batteries.
Light ring:
Visual indication of your
radon levels.
Green: Good
Yellow: Warning
Red: Danger
See separate section for more
details.
Air inlets:
This is where air comes into your
detector. Keep it unobstructed.
Audio/alarm:
Receive an audio alert from your
detector when radon levels are
above recommended level.
Audio settings can be customized
in the app.
Wave sensor:
Simply wave in front of your
detector to activate the light ring.
In case of audio alerts, wave in
front of the detector to snooze.
Tap:
Gently knock on your detector to
start pairing or check connection
status.
Wave
To Next Page
Need help?
General
Weight and Dimensions
