Akai APR-2418

CALENDAR SETTING
When the display show the time, press the MODE button (17) once, it show calendar mode.
• Press SET button once (3) to select the year Turn the Tune + / - knob to set the
correct year Press SET button (3) again to select the month Turn the Tune + / - knob
to set the correct month
• Press SET button (3) again to select the day
• Turn the Tune + / - knob to set the correct day
• Press SET button (3) to confirm the calendar setting
ALARM SETTING
Make sure the POWER switch is set to the 'Off' position. The time or alarm time cannot be set
or adjusted while the unit is 'On'.
• Press the Alarm button (13) and select the Alarm 1 or Alarm 2
• Press the SET button (3) and the display will show the minute 00 will flash and press
Tune +/- to select the minute.
• Press the SET button (3) again to confirm setting, then the Display will show 00:00
and
the first 00 will flash, then press Tune +/- to select the correct hours.
• Press SET button (3) to confirm the alarm setting
• Press ALARM button (13) to enter in normal clock mode
ALARM OFF
During Alarm on, press SET button (3) or ON/OFF button (11). The alarm sound goes off but
the Alarm setting remains.
ALARM VOLUME SETTING
In Radio Alarm, the Alarm Volume is set with the last volume level used during playback.
In Buzzer Alarm, the Alarm level is fixed.
WAKE TO BUZZER ALARM
•
Alarm 1 and Alarm 2 both have “wake to buzzer Alarm” function
•
Set the Alarm time as shown above
•
Turn the Tuning knob to set Alarm to wake up to Buzzer alarm
WAKE TO MUSIC
Repeat the steps of Alarm Time Setting, Alarm 1 and Alarm 2 both have the “wake to music”
function.
• Press the Alarm button (13) once to set the desired Alarm 1 time
• Press the Alarm button (13) twice to set the desired Alarm 2 time
• Turn the Tune +/- knob once after alarm setting to activate wake to Radio function
• After finish the Alarm 1 or Alarm 2 time setting, press the SET button (3) once to confirm
alarm timer setting
• The Radio Memory icon appear in the display. During that time, turn the Tuning +/-
knob to select the desired Radio station stored in the memory before
• Press the Set button (3) to confirm
• Press the ON/OFF button (11) to turn ON the unit, then adjust the Volume to the
desired level. Press the ON/OFF button (11) to switch OFF the Radio, then it switch ON
automatically at the preset Alarm time
SNOOZE / SLEEP
SLEEP FUNCTION
• Press ON button (11) to switch ON the radio. Press the Snooze / Sleep Button (7) sequentially
to display will show 90, press again is 80/70/60/50 ..... 10, then press again is off.
• After set the Sleep function and when finish, then the unit will off automatically.
SNOOZE
The alarm can be
temporarily turned off manually by pressing the SNOOZE button; the
alarm will turn back on  minutes later automatically.
This feature can be repeated endlessly.
HEADPHONES
Headphones should have a 3.5mm diameter stereo plug and an impedance of 8-32 ohms.
When headphones are connected (8), the speaker is automatically disconnected.
SPECIFICATIONS
Power Supply
AC: 230V ~ 50Hz
DC: 4 x UM3 Battery (battery not included)
Radio Frequency Coverage
FM: 88-108 MHz
MW: 540-1600 kHz
SW: 3.16-18.10 MHz in 10 bands
Speaker 4 Ohms, 3-5W
Output power: 0.8W RMS, 10% THD
General
Headphone: 3.5mm jack plug, 8-32W
Impedance 32 Ohms
Specifications and the design are subject to possible modifications without notice due to
improvement.
EN EN 