EasyManua.ls Logo

Alemite 3670 - User Manual

Alemite 3670
18 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SER 3670
Revision (
06-11)
Alemite, LLC
167 Roweland Drive, Johnson City, Tennessee 37601
ww
w.alemite.com
Copyright
©
2011 by Alemite, LLC
This document contains confidential information that is the property of Alemite, LLC
and is not to be copied, used, or disclosed to others without express written permission.
Service Guide
Electronic Metered Control Valve
670889
Description
CAUTION
Do not operate this metered valve with an antifreeze
and water mixture. Meter will not register properly.
The metered control valve models included in the 3670
series are designed to meter quantities of a variety of fluids.
These valve assemblies dispense motor oils (SAE 5-50), gear
oils (SAE 80-240), and automatic-transmission fluid. Each
control valve contains a 40-mesh strainer. The meter's unit of
meas
ure can be programmed for pints, quarts, gallons or liters.
Figure 1
Electronic Metered Control Valve Model 3670 Series -
M
odel 3671-B Shown
Operation
To begin, press the button in the center of the lever. This
releases the safety. With the button held, squeeze the lever
to open
the valve.
T
o latch the valve in the full open position, release the
lever (while pressing the button), then release the button.
To shut the
valve off, press the lever and release.
NOT
E
: The latch feature can be disabled with the
removal of a roll pin. See
Figure 4
.
Ref
er to Service Guide
SER 3679
for meter description
and o
peration.
Fluid Inlet (Swivel) 1/2" NPTF (f)
Maximum Operating Pressure 1000 psi (70 bar)
Fluid Metered
Oil
Oil
Oil
Oil
Oil
Oil
Oil
Oil
Transmission Fluid
Transmission Fluid
Transmission Fluid
Transmission Fluid
Gea
r Oil
Gea
r Oil
Oil
Model
3670
3670-A (obsolete, use 3670)
3670-B
3670-BL (obsolete, use 3670-B)
3671
3671-A (obsolete, use 3671)
3671-B
3671-BL (obsolete, use 3671-B)
3672 (obsolete, use 3671)
3672-A (obsolete, use 3671)
3672-B (obsolete, use 3671-B)
3672-BL (obsolete, use 3671-B)
3673
3673-L (obsolete, use 3673)
3674-C
3674-
CL (obsolete, use 3674-C) Oil
Extension
Rigid
Rigid
Rigid
Rigid
Flexible
Flexible
Flexible
Flexible
Flexible
Flexible
Flexible
Flexible
Rigid
Rigid
Rigid
Rigid
Nozzle Type
Non-Drip Auto
Non-Drip Auto
Non-Drip Manual
Non-Drip Manual
Non-Drip Auto
Non-Drip Auto
Non-Drip Manual
Non-Drip Manual
Non-Drip Auto
Non-Drip Auto
Non-Drip Manual
Non-Drip Manual
Non-Drip Auto. w/ Manual Lock
Non-Drip Auto. w/ Manual Lock
Non-Drip High-Voulme Manual
Non-Drip High-Voulme Manual
Un
its of Measure
(preprogrammed)
Quart
Liter
Quart
Li
ter
Quart
Liter
Quart
Li
ter
Quart
Liter
Quart
Li
ter
Pint
Li
ter
Gallon
Li
ter
Note: Al
l meters are programable for Pints, Quarts, Gallons and Liters (see SER 3679)
3670 3670-A 3670-B
3670-BL 3671 3671-A
3671-B 3671-BL 3672
3672-A 3672-B 3672-BL
3673 3673-L 3674-B
3674-BL 3674-C 3674-CL

Questions and Answers

  • P
    pattysavageAug 12, 2025
    What to do if there is reduced product flow in my Alemite 3670?
    • W
      whiteheadanthonyAug 12, 2025
      If you notice reduced or zero product flow in your Alemite Control Unit, the issue might stem from a few potential causes. First, check for clogs in the system strainer or control valve strainer and clean them if necessary. Second, the metering gears might be jammed, requiring an overhaul. Lastly, ensure that the manual nozzle is fully open.
  • O
    Oscar BakerAug 16, 2025
    Why is my Alemite 3670 Control Unit experiencing continuous product flow?
    • F
      Fred MendozaAug 16, 2025
      If the Alemite Control Unit experiences continuous product flow, it could be due to foreign material on the seal or a worn/damaged seal. To resolve this: * Disassemble, clean, and inspect the seat area, paying attention to mating surfaces. * Replace the seal if necessary. * Identify and eliminate the source of any foreign material. * Clean the strainer. Alternatively, you can use Kit 393676.
  • R
    Richard JohnstonAug 19, 2025
    How to fix leakage at the Swivel Assembly (2j) of my Alemite Control Unit?
    • C
      Catherine SalazarAug 20, 2025
      If you observe leakage at the Swivel Assembly of your Alemite Control Unit, it could be due to insufficient initial tightening or a worn/damaged O-Ring. Try tightening the Swivel Assembly first. If the leak persists, replace the O-Ring.
  • F
    fcollinsAug 23, 2025
    What to do if there is leakage at the Extension Assembly of my Alemite 3670?
    • J
      Joshua ArnoldAug 25, 2025
      If you find leakage at the Extension Assembly of your Alemite Control Unit, it may be caused by insufficient initial tightening or missing/inadequate thread sealant. First, try tightening the leaking connection. If that doesn't solve the problem, apply thread sealant to the male pipe threads.
  • K
    kellievansAug 27, 2025
    Why doesn't the safety on the Lever Assembly (2k) of my Alemite 3670 engage?
    • A
      angelwilsonAug 27, 2025
      If the Safety on the Lever Assembly of your Alemite Control Unit does not engage, it could be due to a broken spring, foreign material, or a worn compression spring. You can try the following: 1. Use Kit 393677. 2. Clean the Lever Assembly. 3. Replace the Compression Spring.
  • S
    Steven EllisAug 31, 2025
    What to do if the latch on the Lever Assembly (2k) of my Alemite 3670 Control Unit does not release?
    • J
      Jeffrey CampbellAug 31, 2025
      If the Latch on the Lever Assembly of your Alemite Control Unit does not release, this could be due to a broken spring, foreign material, or a worn compression spring. Consider the following solutions: 1. Use Kit 393677. 2. Clean the Lever Assembly. 3. Replace the Compression Spring.
  • J
    jeremymorganSep 4, 2025
    How to fix leakage at the Cam (2p) of my Alemite 3670?
    • M
      Matthew HowardSep 4, 2025
      If you notice leakage at the Cam of your Alemite Control Unit, the O-Rings are likely worn or damaged. The suggested solution is to replace the O-Rings.
  • B
    Brittany MirandaSep 7, 2025
    What causes leakage at the front end of the Nozzle in my Alemite Control Unit?
    • Y
      yturnerSep 7, 2025
      If there's leakage at the front end of the Nozzle on your Alemite Control Unit, the nozzle is probably damaged and needs to be replaced.

Alemite 3670 Specifications

General IconGeneral
BrandAlemite
Model3670
CategoryControl Unit
LanguageEnglish

Related product manuals