7
6. Use electrical t6. Use electrical tape to wrap. Be sure to cover the wire ape to wrap. Be sure to cover the wire about two inches on eitherabout two inches on either
side of the connection. First pull side of the connection. First pull the wire that you have just connected along the wire that you have just connected along
side the wire you connected to, tside the wire you connected to, tape and wire tie them togetherape and wire tie them together. Use this method. Use this method
for all connections.for all connections.
CAUTION:CAUTION: All wires must be wrapped with tAll wires must be wrapped with tape and wire tied.ape and wire tied.
2. 2. TTwist upper wires togetherwist upper wires together, twist lower wires together , twist lower wires together as shown.as shown.
1. When tying two sep1. When tying two separate wires together at their ends, strip back 1 of insulationarate wires together at their ends, strip back 1 of insulation
on both wires and sepon both wires and separate arate the strands of wire as shown belowthe strands of wire as shown below..
MAKING END MAKING END TTO END CONNECTIONSO END CONNECTIONS
MAKING CONNECTIONS
Wire Wire TTieie
Electrical Electrical TTapeape
4. Insert the wire(s) from the st4. Insert the wire(s) from the starter through the hole as shown. If arter through the hole as shown. If two or more wires are inserted,two or more wires are inserted,
wrap them in opposite directions.wrap them in opposite directions.
5.5. WWrap the wire around one side then the other and finally around irap the wire around one side then the other and finally around ittself as shown.self as shown.
11
22
33
Use this method ONLUse this method ONLYY when connecting two sep when connecting two separate wires end to end.arate wires end to end.
18
3. Sep3. Separate the vehicle wire(s) as shown. Make the separate the vehicle wire(s) as shown. Make the separation large enough to fit the otheraration large enough to fit the other
wire through.wire through.
2. S2. Strip back one inch of insulation on the wire you need to connecttrip back one inch of insulation on the wire you need to connect to. to.
One Inch of Bare WireOne Inch of Bare Wire
ManufacturerManufacturer Make/ Make/ YYearear Anti-thefAnti-theftt
CHRYSLER CONCORD 98+ TRANSPONDER
(GREY KEY ONLY)
LHS 98+ TRANSPONDER
(GREY KEY ONLY)
SEBRING CONV. 98+ TRANSPONDER
(GREY KEY ONLY)
DODGE 300M 99+ TRANSPONDER
(GREY KEY ONLY)
INTREPID 98+ TRANSPONDER
(GREY KEY ONLY)
NEON 2000+ TRANSPONDER
(GREY KEY ONLY)
FORD CONTOUR 97+ TRANSPONDER
(Some)
CROWN VICTORIA 98+ TRANSPONDER
EXCURSION 2000+ TRANSPONDER
EXPEDITION 97+ TRANSPONDER
EXPLORER 97+ TRANSPONDER
FOCUS 2000+ TRANSPONDER
MUSTANG 98+ TRANSPONDER
F150/250 98+ TRANSPONDER
RANGER 99+ TRANSPONDER
TAURUS 96+ TRANSPONDER
WINDSTAR 2000+ TRANSPONDER
GMC DENALI 99+ PASSLOCK 2
ENVOY 99+ PASSLOCK 2
S-15 JIMMY 98+ PASSLOCK 2
SAFARI 98+ PASSLOCK 2
SIERRA 98+ PASSLOCK 2
SONOMA 98+ PASSLOCK 2
SUBURBAN 98+ PASSLOCK 2
YUKON 98+ PASSLOCK 2
YUKON XL 2000+ PASSLOCK 2
HONDA ACCORD 98+ TRANSPONDER
ODYSSEY 98+ TRANSPONDER
PRELUDE 98+ TRANSPONDER
S2000 TRANSPONDER
INFINITY I30 98+ TRANSPONDER
Q45 98+ TRANSPONDER
QX4 98+ TRANSPONDER
JAGUAR ALL 98+ TRANSPONDER
JEEP GRAND CHEROKEE 99+ TRANSPONDER
(GREY KEY ONLY)
WRANGLER 99+ TRANSPONDER
(GREY KEY ONLY)
LEXUS ALL 97+ TRANSPONDER
VEHICLES WITH FACTORY
ANTI-THEFT SYSTEMS
To Next Page
Loading...