Alfa Network WiFi-Camp Pro 2 - User Manual

Extend and Share Wi-Fi Signal
Installation Guide
To Infinity and Beyond
1
2
3
1
Package Content
Thank you for choosing Camp Pro 2 Hotspot Wi-Fi Extender.
The following items should be inside your retail box:
• 1 x Camp Pro Wi-Fi Extender Router (R36A)
• 1 x Tube-U
(
N
)
USB Outdoor Signal Receiver
• 1 x AOA-2409TF Outdoor 9 dBi Antenna for Tube-U
(
N
)
• 1 x Omni 5 dBi antenna for use with R36A
• 1 x DC Power Adapter for Camp Pro Wi-Fi Extender Router
• 1 x Outdoor Water-Resistant Tape for securing antenna
with Tube
• 1 x Car 12v Charger for Camp Pro Wi-Fi Extender Router
power supply
• 1 x USB cable for connecting Camp Pro Wi-Fi Extender
Router and Tube-U(N)
Hardware Installation
1. Mount the antenna AOA-2409TF to Tube-U
(
N
)
securely, and seal the gap on
the N-type connector with weather-resistant tape.
2. Mount the omni antenna to Camp Pro Wi-Fi Extender Router, and connect
Tube-U
(
N
)
with R36A via USB cable provided in the package.
3. Connect the power adapter to the
Camp Pro Wi-Fi Extender Router.
How to Start WiFi-CampPro 2 Device Configurations
Before proceeding any further, please make sure the USB LED on CampPro
WiFi Externder is “ON”.
3
2
1
When Ethernet connection is made, the LAN1 LED will be “ON”.
- Via wired connection :
Connect computer to CampPro Wi-Fi Extender
Router LAN1 port via Ethernet RJ-45 cable.
Open your web browser, and type-in
“wificamppro2.myalfasetup.com” or
“192.168.36.1” in the address bar.
- Via wireless connection :
On your laptop, tablet computer or
smartphone, enable WiFi service on your
device, and search WiFi name“WiFiCamp
Pro2-xxxxxx”, then associate with it.
Open your web browser, and type-in
“wificamppro2.myalfasetup.com” or
“192.168.36.1” in the address bar.
- Via QR code connection :
On smartphone/tablet device, search WiFi name “WiFiCampPro2-xxxxxx”,
and associate with it.
Run QR code reader app, and read the QR code sticker on WiFi Extender.
192.168.36.1
Set Up
LAN2 PoE LAN1 PWRANT
wificamppro2.myalfasetup.com
In QR code app, select “Open URL”, and device portal page will be shown.
About running QR code app on Android and iOS devices:
iOS 11 or later: please use built-in camera app to read the QR code.
If there is no QR code scanner/reader in your smart phone, please search
free "QR
reader" on the Apple App Store or Android Play Store, and install it to read the QR
code from device.

Summary

Package Content

Hardware Installation

How to Start WiFi-CampPro 2 Device Configurations

Via wired connection

Connect computer to CampPro Wi-Fi Extender Router LAN1 port via Ethernet RJ-45 cable and access setup.

Via wireless connection

Enable WiFi on your device, search for WiFi name "WiFiCampPro2-xxxxxx", and associate with it.

Via QR code connection

Search for WiFi name "WiFiCampPro2-xxxxxx", associate, then use a QR code reader app.

Connecting WiFi-CampPro 2 to Remote WiFi HotSpot Station

Device Management Password Setup

Setup a device management password for secure access to the device portal.

Select Target Access Point

Scan for available hotspot signals and select the target network to extend.

WiFi-CampPro 2 Connection Status

View the connection status with the target hotspot and connected clients.

CampPro WiFi Settings

Configure a preferred SSID and Wi-Fi password for users to connect to the extender.

Alfa Network WiFi-Camp Pro 2 Specifications

General

Frequency Band	2.4 GHz
Max Data Rate	150 Mbps
Security	WEP, WPA, WPA2
Humidity	10% to 90% non-condensing
Wireless Standards	802.11 b/g/n
Antenna Type	Omni-directional
Operating Temperature	0°C ~ 40°C
Ports	1 x 10/100 Mbps Ethernet