Why is my alfaplam Wood stove not hot enough for baking?
If your alfaplam Wood stove isn't providing enough heat for baking or cooking, it could be because the thermostat is set to a low temperature. Increase the water temperature using the thermostat or briefly open the ash pan door.
What to do if alfaplam Wood stove circulation pump is not working?
If the circulation pump of your alfaplam Wood stove doesn't activate or trips the switch, it could be due to several reasons: * There might be no power at the electrical connection, or the connectors are loose. Check and tighten all screws at the connection points. Also, check and replace the switches if necessary, and fix any motor connection or installation connection problems. * The capacitor could be faulty, requiring a replacement. * The rotor might be blocked. Check whether the rotor turns easily each time you start heating. Hot water deposits can cause the rotor to block. Turn the motor axis left and right using a screw gun until the rotor can move freely. * The pump could be blocked due to deposits. In this case, dismantle and clean the pump.
Why is my alfaplam Wood stove boiler-stove smoking?
Your alfaplam Wood stove boiler-stove might be smoking during regular use due to: * The chimney, flue pipes, and stove may not be cleaned. Clean the inside of the chimney, flue pipes, and stove. * The fuel may be wet, or you are using fuel that generates a lot of smoke. Change the fuel to dry or smokeless fuel. * The firebox may be overloaded. Gradually fill the firebox in several steps. * The chimney may be of poor quality. Repair your chimney or build a new one.
What to do if alfaplam Wood stove safety valve is not discharging water?
If the pressure in your alfaplam Wood stove system is over 3 (2.5) bar and the safety valve isn't discharging water, it's likely that the safety valve is faulty and needs to be replaced.
How to fix alfaplam Wood stove water pressure dropping?
If the water pressure in your alfaplam Wood stove system is slowly dropping, it could be due to an unsealed installation. Check whether all welded connections, threaded connections, unions, etc., are sealed.
Why is my alfaplam Wood stove cooling thermo fuse activated?
The cooling thermo fuse (thermo valve) in your alfaplam Wood stove may activate due to a water temperature rise over 95°C, which can be caused by: * A power outage: Do not touch anything. When the system has cooled down, the thermo valve will close itself. * An open ash pan door and no controlled combustion: Close the ash pan door and reduce system water temperature using the knob on the ash pan door and thermostat. * The grate being in the down position and not many radiators being open: Switch the grate to the up position or open more radiators. Keep the ash pan door closed.
Why safety valve isn't discharging water from alfaplam Wood stove?
If the safety valve of your alfaplam Wood stove is not discharging water from the system and the pressure is below 3 (2.5) bar, it is likely that the safety valve is faulty and needs to be replaced.
Why is my alfaplam Wood stove too hot for baking?
If your alfaplam Wood stove is producing excessive heat for baking or cooking, it's likely that the thermostat is set to a high temperature. Reduce the water temperature using the thermostat or burn a smaller fire.
What causes sudden water pressure rise in alfaplam Wood stove?
A sudden water pressure rise in your alfaplam Wood stove system, due to water temperature increase, can be caused by: * Reduced expansion vessel pressure or the vessel being completely empty. If water is leaking from the valve, replace the expansion vessel. If only air is coming out from the valve, remove the vessel from the system and apply additional pumping. Vessel pressure should be equal to or higher than the height difference between the highest and lowest point of the system. For example, for a 5 m height difference, the pressure equals Pmin ? 0.5 bar. * Air in the system. Release air from the system.
What causes low outlet water temperature in alfaplam Wood stove?
If the outlet water temperature of your alfaplam Wood stove is too low, it could be because of: * Low calorific value of the fuel. Change the fuel. * Oversized heating system (too many radiators). Turn off some radiators. * Not enough fuel has been loaded in the firebox. Increase the quantity of fuel in the firebox.
General| Brand | alfaplam |
|---|---|
| Model | ALFA TERM-27 |
| Category | Wood stove |
| Language | English |
To Next Page