Align 3GX Compact - Page 10

5. A.REV AILERON REVERSE SETUP MODE
A.REV IRCREERORERH
direction
eaBenna
direction
+FREEDA
Helicopter tilting
direction
RA
=>
Helicopter tilting
Swashplate correction
Press the SET button to enter A.REV setup mode. The A.REV LED]
will lit up after A.LIM turns off. Tilt the helicopter right as shown
in diagram, and check if swashplate is tilting correctly toward the
left. If the swashplate is tilting at the wrong direction, move the
transmitter aileron stick until STATUS LED changes color, and
re-check the swashplate ig direction. Press the SET button
again, and the control unit will restart with all LED's flashing.
This completes the flybarless portion of the setup process.
EBT "SET'R > BAER AEA"A.REVEI MICS ERG" REET > HF
ALIMIBISHi > A.REVIEZE < MARTLERIMICMMISE IG » UREA
GIA > 3GX FlybarlessfEiG+FROAMIZIE URRA: TATNOSHE)
BIES » BR "STATUS" ASABE » SRICKBIZIEIA
HESIT "SET" RENAE GRAMME » A BLEDISPIED > SRT «
3GX Flybarless system must remain A.REV settings
stationary during startup. Do not move the | NOSY sy
helicopter until the swashplate jumps up and
down slightly 3 times, indicating the
completion of initialization.
3GX
Flybarless
834405
i
Oe
ieee
ADEDE + SUMS +FRARG
ABLE PN MEREIR > RTH °
3GX THROTTLE CALIBRATION 3Gxiais23 PST
Throttle/Pitch curve Press 3GX SET “Turn on the receiver Leo. w 3GX panel all
BPE butto power
d
7
eK
LED;
While
setting
throttle
IQBSCX
SETEN
eek
ci
ue
RPE,
calibration, reset throttle
curve and pitch curve to
default 0-50-100.
EROP HTIERIE » SEHR
/MREBEBRRICIEE)
FARR
O
50
10082
E.
Move
the
throttle
After
finish
the
setup,
red
Release
SET
button
stick
from
lowest
and green LED start Take off the
to highest point italy ing and 3GX restarts receiver spar
ne rent HES eee 4 GR PAE
BATT <2 ESC
FLIGHT MODE SETTING RASH
Operation Instrution
BRERROA
2. it ARIE KS TATUSAYIE SEB PIRO BLN REA BUSA +
Double flash: El
Flash in group of
Flash in group of
Flash in group of
Move rudder stick
ORs
1. With 3GX in operation mode, push rudder to left or right, and press the SET button for about a second.
2. After entering setting mode, the STATUS LED will flash specific number of times to indicate specific settings.
3. During setting process, LED1 to 5 indicate the rate of setting; flashing LED represents 10%, while steady lit LED represents 20%.
For example, if LED1 and LED2 are steady lit with LED3 flashing, the set rate is 2*20+10=50%.
1. EEIGXB (EARP ENER REABROBAL » RBRSETRI—W »
3. FERRI PLED1~S{U RIVA > LEDRI% » LEDEZRR20% + HIMILED1~LED22% » LEDSPGI# + ERT (H732*20+10=50% -+
The LED flashing frequency indicates setting position.
Single
flash:
le
rate
adjustment
Fully
lit
LED4
indicates
20%
levator end point settin:
indi
A
Ailerontend
point Setting
Fully lit LED2 indicates 20%
Flashing LEDS indicates 10%
: Stash campeningise So the setting value is 2*20+10=50%
LEDIERARR20%
LEDE RI R20%
LEDSPS HEIR R10%