Align 3GX Compact - Page 13

3GX Flybarless g MERR REAR SSRN GIRBBH760 u sA ( WFutaba $9256 - $9251 - BLS251) > AlW\AiG3GX FlybarlessHPL KS
TEOKRT
>
FAIR
u
SIREIR
—RER1520
u
SHEE»
MATE
AS
1S2OGHET
-
EA DAES : HER CAD" SET RESH > IEI" STATUS"; METE STRA aA 520/760" (Eee Teer RAVENS
ee ee FIFE HOMIE CHORES eS » HIT ORIE EA (XH) "STATUS" ETIE RRE * MEE IEA1520 usA
BREET u SRG” MARED DERIER * STATUS "ETERS GEA TOO u SKA °
30x A barli 74 7" STATUS" E. SET" @— ROH A Ft > KEM AA
ASX year les SBE ol iis RERI R LENS BIER: arent RERNAIR" RUE, BRE RAOMAR
Green LED : 1520 1s standard band
Red LED : 760 y s narrow band
ARE : 1520 u SWAAR
MB: 760usFAARE
EN
#LZLL. Slee
sa
l l
Standard/Narrow
band
mode
E
RUD
Eg
RR ERES, Mode 4 Mode 2
Select by moving the rudder stick left and right
ZbRHF OAR
2.DS (DIGITAL) / AS (ANALOG) SERVO SELECTION Dsgyii_/AS#Att ARSE
There is a direct correlation between servos' speed to gyro's performance. Faster servos are able to execute commands from
the gyro at faster and higher precision. Due to the high performance gyro sensors used in the 3GX flybarless system, premium
high speed digital rudder servos are mandatory for optimal tail performance. Some of the recommended rudder servos.
Setup method : Press and hold the SET button for 2 seconds to enter the setup mode, then press the SET button to select
DS/AS setup mode, as indicated by the lighting of DS/AS LED. Using the transmitter's rudder stick, select either digital servo
DS mode (STATUS LED is green),or analog servo AS mode (STATUS LED is red).
DAR SSM ERR ARICA » VARSEMD/ERUR » SALTER RPC AHOVIED » AMR BI MAE : FADSGX FlybarlessA BBS RHR
KORRES » PTLAR EM ICS Bc RD WL ARES » LAMPS AREAS
QED
:
RASET
MAE
ADAM
+
BR"
SET’
RIEDS
/AS
RIAs
(DS
ASHE
TIGRE
)»
AAAS
ACE
PSRIERUDS
(STATUSAR
)
DALAS
(STATUS
AS34118)
(ARSE
°
N}/Using
an analog servo in DS mode will
cause damages
to the servo.
FEDS FEH" ASAR te (DAR 8S" GBH DAR EBS ©
Select by moving the rudder stick left and right
ZSBOD ORB
Green LED : DS digital servo
Red LED : AS analog servo
Ne : DSM TBARS
J : ASHKARE
Digital
/
analog
mode
ps
13)
RUD
9;
MiMe
Mode
1
3. RUDDER SERVO DIRECTION CHECK AND LINK ADJUSTMENT ERRAREELEIANRAE E
Move the transmitter rudder.stick left/right, and check for the correct direction of the rudder servo. If needed, servo
reverse is done fromthe transmitter's REV (reverse) function.
For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode (non-heading
lock), or press and hold the SET button for 2 seconds. With the rudder servo centered and servo horn at 90 degrees,
adjust the linkage length until tail pitch slider is centered on the tail output shaft as shown in diagram.
ZGROBMES CVERAIRKBSHOHOLSLE STABLES OSCARS ELSI -
183GX Flybarlesst) MN FEMERNNIGA"SET RAD » PVICAGRBRIGEPURVIUEL » BRGRICK » MOR SMC BSA IRM S90 » He:
HBB REGePitch PAEH -
Approx. 10mm
PP Omm
Tail servo Hom!
SORES
4.GYRO
NOR/REV
SETTING
nor
/REVICSRRERGMBRE
Lift up the helicopter by hand, and turn it to the left (yaw). Check if the rudder servo is applying correct compensation to the
right. If reversed, set the NOR/REV setting as follow.
Setup method : Press and hold the SET button for 2 seconds to enter the setup mode, then press the SET button to select
NORIREV setup mode, as indicated by the lighting of NOR/REV LED. Using the transmitter's rudder stick, select either NOR
(STATUS LED is green),or REV (STATUS LED is red).
RRGAR SOARES SLLAIRKVEDHORESROIORESISROADOK + AAR SNM ESORELE > SALEHRSAERORE ©
BRET
:
HR"SET
MAE
A
DREN
»
RNOR
/REVBIR
+
LG
GR
BZNOR(
STATUSAME
)
NREV
(
STATUSZH#TIS
)
+