Align 3GX Compact - Page 15

er Gen “Mise Pet eenOn Kemi COeManes CARERS ENDE. T005 “PSSESRR
BEDR : HR"SET" WEA WARES » RISB DELAY IR > be tant Te SHZAVBA 20 : T-REX 250/450 (STATUS #A1IS) > oo
‘EL 220 T-REX500/550/600/700/800 ( STATUS SZI) > SISE DELAY iFAR HAARE RRE » ERP,
pes ame IERASTO% > A HE RIONN EPHEDRA SIT RISA * We RSET" RER > GooM erat
Gradually move the transmitter rudder stick until DELAY
Green LED for T-REX800 LED begins to flash, the delay value is 0% at this point.
i
SEDARE DELAY ERAPR » EEE
EIER Rup E 0
Mode 1 Mode 2
0% when DELAY LED
begins flashing Continue to move the rudder stick until desired delay value is
DELAYIE
PA
t
PS
M8
65
230%
needed,
then
press
the
SET
button
to
register
the
setting.
Maximum is 100% delay, with rudder stick pushed to the end.
FAREB RATE 128100% EREEREER + aE
"SET" SENEI
Green LED for T-REX800
T-REX80039 E.
Eim Om dE
Sem N
«2G Rey CHR
7.ANTI TORQUE COMPENSATION DIRECTION SETTING RinHRERGRE |]
To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function. User. need to confirmif
3GX is mounted right side up or upside down.
Right side up: Installed with 3GX label facing up, anti-torque compensation set to positive (green STATUS LED).
Upside down: Installed with 3GX label facing down, anti-torque compensation set to negative(red STATUS LED).
AERCMMRA TS — BM » SGX PY RIB TID AE, (BAAS AB HE BBG X Ma IF SRL ZB ©
TER : BIRIGSGXE ARAL » RIRAIRIRAIER(STATUS#RIB) +
FR : IRAGISXDARGE BR + RIBERA (STATUSALIE) ©
Setup method: Press and hold the SET button for 2 seconds to enter setup mode, select until anti-torque compensation section, as
indicated by lighting of all 5 setup mode LEDs. Using the rudder stick to select either positive anti-torque compensation (green
STATUS LED) for right side up mounting, or negative anti-torque compensation (red STATUS LED)for upside down installation.
BYES : (HR SET MAM te A ALARA WEE AGINTEA > HOSSAIN OE EENDEN WIER » AREA
IE((STATUSERIS) ; BIGX > ue AC aNSTATUSIE) a
Green : Right side up mounting
Red : Upside down mounting
Select by moving the rudder stick left and right
ESRBJALRE
Ñ| RuD 3
Mode 1 Mode 2
Anti Torque Compensation
direction setting
BBE RIE S
8.SENSITIVITY ADJUSTMENT SERE
For radio with built in gyro gain settings, gain can be adjusted directly. For example, 50%-100% setting on the radio translates to 0% -
100% gain in the heading lock mode ;50%-0% setting on the radio translates to 0%-100% gain in the normal (non-heading) lock mode.
Actual gain value differs amongst servos and helicopters. The goal is to find the maximum gain without tail hunting. This can only
be done through actual flight tests.
The recommended starting point for transmitter's gyro gain setting should be 70~80% for hovering, 60~70% for idle-up. Value should
be tuned under actual flight conditions by increasing to the maximum gain without tail hunting.
RABI ee DRR EES» CE \CYROMAEMRE TEENIE > BEESON RIERO RRAO + BLEIESO%~100% > RIREIRIR RSE
AMEMREEIO~100% + 8E050%~-0% > RIRE REEE ERE0~100%
VEENA \SASORSREAROTAMAMZR RMS ETEESRRS (GABSMLRA ISRO ) CAE NORMS : MURE
MAARN T OU re RET aS ©
EATERS RUS ATER + MIBDIS POSER ARE TE70~80% 7H > Idle up RRR ETTA » CRBRKARNIREBTICL URRAEM
RRVTHISMBSGE » Set SHR AERE -
For radios (IE Futaba) using 0-100% as heading lock gain scales, the recommended gain setting is 30% to 35%.
For radio that uses the 50 -100% scale(such as JR and Hitec), the recommended gain setting is 70% to 75%.
SAREE IG 730~100%0) E298 » YOFutaba » PARETI- + MEGS A50~100%A S288 » MYR -HITEC - VA MSSMEL-~-7S%2S |
Specifications Æi
1.Operating voltage range : 6.Operating temperature : -20°C~65°C 1.382 : DC 3.5V~8.4V 6482/5 : -200~65C
DC 3.5V~8.4V 7.Operating humidity : 0% ~95% 2B : <80mMA @ 4.8V TRIER : 0%~95%.
2.Operating
current
consumption
:
8.Dimension/Weight
:
S/SRIAIRRATRBRE
:
+300%sec
BRUSH:
<80mA
@
4.8V
36.5x25.2x15.6mm/
11g
4/58)
2ERE
:
+600°/sec
36.5x25.2x15.6mm/11g
3.Rotational detection rate : +300°/sec @ROHS certification stamp
4.Rudder yaw detection rate : +600°/sec
5.Sensor resolution : 12bit
SEERNE : 12bit(12{770) OF ERHSRARE