Align 3GX Compact - Page 5

SETUP PRE-CHECK 22888
While using 3GX FBL system, be sure to turn off the following functions in the transmitter
EHIGCKAMEREZSA NDS RDA
* Swash Ring _* Linkage Compensation * Swash Mix * Mixing * Acceleration
1. Connect the receiver and servos to the flybarless control unit as per diagram found on page 4~5
2. Digital servos must be used on cyclic to avoid damage to servos.
commended servo spec: minimum speed 0.08 sec/60; torque 12kg.cm or higher.
3. The trim must be zero when using 3GX, and should not be adjusted at anytime. If the helicopter hovering tend to one side, it
means the swashplate doesn't keep horizontal when setting. Go to flybarless system "Direct mode bypassing gyro, for
mechanical travel and neutral point setup" to adjust the level of the swashplate and then re-complete the setup.
4. When the 3GX Flybarless system is installed for the first time, a few simple setup steps and fly tests need to be performed in the
flybarless setup mode. these steps need to be performed only durin: tial setup, and does not need to be repeated for sub-se
quent flights. Just power up the system normally, check the proper servo operations, and fly. The initial setup procedure only
need to be repeated after software upgrade, pitch range reset, or subtrims are added in the transmitter.
1. REMBRARBKERTRO BE (WSRA4~ A) >
2. +FRUARR AUTRE > SABER - BARB : E0.08W/60° MA : 197)12kg.cmLLE +
3. AREA AS EN MRS RIFTKIBEAMS SEARSRROR-BED) ATREH+FRARSKE MEARE ORAR BT
PAPUIMQE" BE+FRLKTR EMNERNE -
4. B-RARIGCX FlybarlessMPT BRAM UALEARPRRNERN » EARO RR ERRITAR TOR TABE AIR ERN > REER
W RERE FEARIN : RIB MIEN - BIEN S SM SSSA MA(sub.trim iy UREA RERNBLR LOAM e
3GX CONNECTIVITY METHOD 3CXERIR
METHOD 1:STANDARD RECEIVER CONNECTIVITY METHOD xt—: RERS ERA
1. Connect all wires as shown in diagram, Receiverand 3GX
wires are color coded to distinguish the different connection
channels..Care should be taken to ensure proper wire color to
channel connection.
2. While using the speed controller that not including BEC, you need
‘to connect the BEC power with 3GX “BATT” port.
3. Receiver power is achieved by connecting the 3GX "S.BUS/BIND"
port to the ch7 or BATT port on receiver using supplied signal wire.
4. To avoididamage to servos, only digital servos should be used for
swashplate. Recommended spec: 0.08s/60' or faster, with 12 Kg
or higher torque.
j. 3GX has built in speed governor function which can be utilized by
urchasing the optional speed sensor. Governor setting is done
through channel 7 on the receiver.
+ BER PRT He FER poumon CRRA TMOREREATA
BUS » RRIF EBSA SHH MS °
PAA RBECH HNDE, ARMA BIGXAN" BATT "FL (17 ABECRM -
$508, 38 T RE DA BA Hd BEA SR RBG XA)"S.BUS/BIND" 51 (i7ie 2 8 bE
SYBATT A i8 »
4. +FRUAS RAAT AIRS » SA BS LIDAR SIAL
IRURI
:
TO.0BM/EOLAPY
:
4712kg
E
+
5. SGX R ERRE TAMERS MASE MEREDEK
BtveeKe
en
HAZ
:Futaba
S.BUSHER
|. For Futaba S.BUS receivers, connect wires as shown in diagram.
.. While using the speed controller that not including BEC, you
need to connect the BEC power with 3GX "BATT" port.
Receiver power is supplied through S.BUS signal wire connected
to3GX's “S.BUS/BIND” port.
The default channel/function mapping when using S.BUS are:
(AIL (2)ELE (3)THR (4)RUD (5)GAIN (6)PIT (7)GOV
AAHS.BUSI BEA) Futabalsigs » SKIRM Tite THER
PARBECH 18M EE ARN. HSCXA" BATT FEA BEC <
EMBSSRAGBS.BU: RIRE BISXA)"S.BUS/BIND"3/{i7 ©
ERS.BUSI
REIS
'
ABMIBDISER
:
(AIL (2)ELE (3)THR (4)RUD (5)GAIN (6)PIT (7)GOV
Pe oye
tated trast
——— If channel (3) is set as PIT and channel (6)set as THR on transmitter,
THR RUD PIT ELE AIL Such as 8FG, 12Z, 14MZ, and etc, please reprogram the transmitter
Esc ie: to utilize channe (3) as THR and channe (6) as PIT.
SPE BOVE ASS (3) EAP IT (6)AISASTHRES > HIUSFG - 12Z -
A4MZS
+
BEES
HVE
AS)BiS
THR
(6AE
PIT
>
. To avoid damage to servos, only digital servos should be used
for swashplate. Recommended spec: 0.08s/60 or faster,
with 12Kg or higher torque.
. 3GX has built in speed governor function which can be utilized by
purchasing the optional speed sensor.
Governor setting is done through channel 7 on the receiver.
G50 OGS . + FARA RITA > SABES ORIER -
Do
not
exchange
AIL
BATT
out
k
Si
nok
ae
land
PIriconnactions:
[ta
FR
J
ERRE
BE0.08/60
DP
:
AIZKg
LE
AILRPITREIHA
©
ee
TABERECARER
SRQEHENBO
p
a
2