What to do if my allen AT14S Trucks does not make use of all its power?
If your allen Trucks isn't performing at its maximum potential, it might be due to using the wrong type of hydrostatic oil. Check the oil and replace it with the correct type if needed. Also, a clogged hydrostatic oil filter can reduce performance, so consider replacing the filter cartridge.
What to do if the engine of my allen Trucks does not start?
If the engine of your allen Trucks fails to start, several factors could be at play. Begin by checking the spark plugs and electrical circuit, replacing them if necessary. Next, inspect the battery for flatness or oxidised terminals, cleaning or replacing as needed. Ensure the fuel tank isn't empty and that the correct fuel type is in use, replacing the fuel after cleaning the tank if it's incorrect. If these steps don't resolve the issue, the starter or electromagnet may be damaged.
Why is my allen Trucks jerking?
The jerking of your allen Trucks can be attributed to several reasons. First, check the oil level in the tank and top-up if necessary. Next, verify the efficiency of the pipes and fittings, as air in the hydraulic drive system can cause jerking. A clogged hydrostatic oil filter can also be a culprit, so replace the filter cartridge. Lastly, ensure that the control levers are operated gently, as abrupt movements can cause the vehicle to jerk.
What to do if my allen Trucks does not move in either direction?
If your allen Trucks isn't moving despite operating the levers, consider these possibilities: damaged cylinder or sealings (verify and replace if necessary); broken hydraulic pipes between the hydrostatic motor and the pump (verify and replace if necessary); or overheated hydraulic oil (wait for the hydraulic oil to cool down sufficiently and try again). If these steps don't solve the problem, the hydrostatic motor and/or pump may be damaged.
What to do if the loading tipper does not rise or tilt in my allen AT14S?
If the loading tipper on your allen Trucks isn't rising or tilting, check for a faulty joint and/or hydraulic pump and replace if necessary. Also, inspect for broken hydraulic pipes and replace them if needed. Finally, verify the distributor pressure and restore it if it's too low.
What to do if one of the two tracks is blocked in my allen Trucks?
If one of the tracks on your allen Trucks is blocked, first check for any foreign body lodged between the track and the chassis and remove it. If there is no foreign body, the hydrostatic motor may be faulty, the pump may be damaged or hydraulic pipes may be broken.
Why is the hydraulic oil excessively overheated in my allen AT14S Trucks?
If the hydraulic oil in your allen Trucks is excessively overheated, it may be due to a low hydraulic oil level. Verify the level and restore if necessary.
What to do if the track tends to come out from its housing in allen AT14S?
If the track on your allen Trucks tends to come out from its housing, it's likely due to a loosened track from use. Adjust it in accordance with the instructions provided in the paragraph CHECKS AND INSPECTIONS of the GENERAL MAINTENANCE.
What to do if the corresponding track does not move despite the lever is operated in my allen AT14S Trucks?
If the track on your allen Trucks isn't moving even when the lever is operated, the hydraulic pump may be faulty or hydraulic pipes may be broken.
Explains the structure and meaning of model and serial number codes.
Details the location of the unit identification plate for record keeping.
Provides detailed measurements and diagrams of the machine's dimensions.
Lists detailed specifications for the machine's engine.
Instructions on recording engine serial number, type, and purchase date.
Covers Proposition 65 and federal respiratory hazard regulations.
Explains safety notes (DANGER, WARNING, CAUTION, NOTICE) and hazard symbols.
Essential safety precautions for operating and maintaining the machine.
Safety instructions for safely lifting and transporting the machine.
Instructions on how to properly position safety retainers for secure operation.
Identification and function of all control levers and buttons on the operator console.
Guidance on basic maneuvers like driving forward, backward, and steering.
Recommendations for vehicle use and troubleshooting track issues.
Routine maintenance tasks including greasing and general checks.
Procedures for track tightening, wheel gear oil, and filter replacement.
Details on hydrostatic transmission, pump maintenance, and pressure checks.
Information on battery maintenance and related electrical system checks.
Common problems, their causes, and recommended solutions for the machine.
Parts lists for the main frame, chassis, and related structural elements.
Components for the engine, fuel tank, and associated parts.
Parts for hydraulic pumps, coolers, hoses, filters, and connections.
Components of the operator console, levers, throttle, and related plates.
Parts for various bucket types, cylinders, and mounting hardware.
Lists decals, maintenance tools, filter kits, and hourmeter components.
A detailed diagram illustrating the hydraulic system layout and components.
A diagram showing the machine's electrical system wiring and components.
Details revisions made to the manual, including dates and reference numbers.
To Next Page
General