ALTA BLISS SURFACE MOUNTED WALL SWITCH

To Next Page

SURFACE MOUNTED

WALL SWITCH

PROGRAMMING AND USERS GUIDE

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada license-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

P1 Button

LED

light

P1 button

Lithium Battery Switch

Power line

Signal line

P1 Button

a. Press and hold “Stop” button more than 15s.

Wall Switch will show “L” (lock).

b. In the next 10s, press one “P2” button on

the back of Wall Switch. Wall Switch will show

“o”, then the Wall Switch switches to “Lock”

mode to disable the following commands:

- Change Motor Direction

- Setting the Upper and Lower Limit

- Adjust Limit

- Roller Mode or Sheer Mode

c. Press and hold “Stop” button more than 15s.

Wall Switch will show “U” (unlock).

d. In the next 10s, press one “P2” button on

the back of Wall Switch. Wall Switch will show

“o”. The Wall Switch now switches to “Unlock”

mode, you can access all control functions.

*This advanced feature is intended to be used

after all shade programming is completed. User

Mode will prevent accidental or unintended

changing of limits.

Lower Channel

LCD Display

DownUp

Higher Channel

Stop

Group Control

Lower Channel

LCD Display

DownUp

Higher Channel

Stop

Group Control

Stop

Action on

Wall Switch

Response

Action on

Wall Switch

Response

Action on

Wall Switch

Response

P2 Button

DECLARATIONS

Voltage 3V (CR2430)

Radio Frequency 433.92 MHz Bi-directional

Transmitting Power 10 milliwatt

Operating Temperature 14°F to 122°F (-10°C to 50°C)

RF Modulation FSK

Lock Function Yes

IP Rating IP20

Transmission Distance up to 200m (outdoor)

SPECIFICATIONS

AMP25B

Instruction

Attention

-1-

The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.

Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Declarations

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

-2-

Safety

1. Do not expose motor to humid, damp or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna and keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If power cable or connector is damaged, do not use.

6. Ensure correct crown and drive adaptor are used.

7. Ensure power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls shall be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

11. Installation and programming to be performed by a qualified professional, use or modification outside

the scope of this instruction may void warranty.

Features

Fields of Application

Specifications

Following data for reference

Working temperature: -10℃ ~ +50℃

Input Voltage: USB 5V 1A / USB 5V 2A

Radio Frequency: 433.925MHz

Maximum Running Time: 6 minutes

Model

Rated Torque

(N.m)

Rated Speed

(rpm)

Rated Power

(W)

AMP25B - 0.7/34 0.7 34 8

AMP25B -1.1/28 1.1 28 8

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and

needs to be charged.

During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped

running and needed to be recharged.

Rechargeable Battery

Blinking red:

Low battery alert

Blinking green:

Charging is processing

Solid green:

Battery has

finished charging.

FCC Text - text 01

Add A zoom in on the

charging port

P1 Button Instructions

P1 button

Lithium Battery Switch

LED light

Micro-USB Port

Add visual explanation of P1 - file 02

Sheer

Roller

Revolve

Roman shades

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

SAFETY INSTRUCTIONS

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna. Keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If the power cable or connector is damaged, do not use.

6. Ensure the power cable and antenna are clear and protected from moving parts.

7. Cable routed through walls should be properly isolated.

8. Motor should be mounted in horizontal position only.

9. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

SAFETY INSTRUCTIONS

Settings Steps

1 Pairing P1 (hold for 2s) > Stop (hold for 2s)

Switch Rotating Direction Up + Down (hold for 2s)

3 Set Upper/Lower Limits

4 Add/Remove Fav. Position P2 > Stop > Stop

5 Roller/Sheer Mode Switch Up + Down (hold for 5s) > Stop

6 Adjusting the Limits

7 Add/Remove a Remote P2 (existing) > P2 (existing) > P2 (new)

8 Speed Regulation

Upper Limit: Up (hold for 2s) > Up + Stop (hold for 2s)

Upper: Up + Stop (hold for 5s) > Up or Dn > Up + Stop (hold for 2s)

Increase Motor Speed: P2 > Up > Up

Lower Limit: Down (hold for 2s) > Down + Stop (hold for 2s)

Lower: Dn + Stop (hold for 5s) > Up or Dn > Dn + Stop (hold for 2s)

Decrease Motor Speed: P2 > Down > Down

QUICK INDEX

TROUBLESHOOTING

Problem - The motor has no response

Cause Solution

Battery in motor is depleted Recharge with compatible AC adaptor and check

connection and positioning of solar panel

Insucient charging from Solar Panel Check connection and orientation of solar panel.

Wall switch battery is discharged Replace battery or check placement.

or not installed properly

Radio interference / shielding Ensure wall switch and the antenna on the motor

are positioned away from metal objects.

Receiver distance is too far Move wall switch to a closer position.

Power failure Check power supply to motor is connected/active.

Incorrect wiring Check that wiring is connected correctly.

Problem - The Motor beeps 10 times when in use

Cause Solution

Battery voltage is low/ SolarPanel Issue Recharge with AC adapter or check connection and

positioning of solar PV panel

Problem - Cannot program a single motor (multiple motors respond)

Cause Solution

Multiple Motors are paired to the same Always reserve a channel for programming.

BEST PRACTICE - Provide an extra 15 channel

remote in your multi-motor projects for individual

control and programming purposes

To work on a single motor at a time, place all other

motors into sleep mode. Press the “P1” button

(about 6 ec) on the motor head until motor jog x2

and beep x2.

HORIZONTAL

BLIND

TILT MOTOR

ROLLER / SHEER

DUAL / WOVEN

MOTOR

HONEYCOMB

CELLULAR

MOTOR

WALL SWITCH OVERVIEW

Please read prior to installation and use. Save these instructions for future reference.

BUTTON INSTRUCTIONS

REPLACING THE BATTERY

a. Unscrew with the screwdriver then gently press down the cover.

b. Install battery (CR2430) with positive (+) side facing up.

c. Gently assemble the cover back and replace screw with screwdriver.

ADVANCED SETTING - DISABLE LIMIT SETTING

Need help?

Do you have a question about the ALTA BLISS SURFACE MOUNTED WALL SWITCH and is the answer not in the manual?

Summary

Wall Switch Overview

Button Instructions

Diagram and labels for the Up, Down, Stop, P1, P2, and LCD display buttons.

Replacing the Battery

Step-by-step guide for unscrewing, replacing the CR2430 battery, and reassembling.

Advanced Setting - Disable Limit Setting

Procedure to lock/unlock motor limit settings using Stop and P2 buttons.

Getting Started

Pair; Unpair Wall Switch

Instructions for pairing or unpairing a wall switch with a motor.

Change Motor Direction

Procedure to reverse the motor's direction of operation if needed.

Setting the Upper and Lower Limits

Guides for setting precise upper and lower movement limits for the motor.

Favorite Position

Instructions on how to set and send the shade to a preferred position.

Add or Remove Additional Wall Switch

Steps to add or remove extra wall switches for motor control.

Adjust Motor Speed

Instructions to increase or decrease the motor's operating speed.

Channel Options

Select a Channel

Using '+' and '-' buttons to navigate and select desired channels.

Hide Unused Channels

Procedure to hide channels not in use by pressing specific buttons.

Roller Mode and Sheer Mode

Roller Shade Mode

Setting the motor for continuous shade movement after a short press.

Sheer Shade Mode

Configuring shade for slight adjustments and longer movement.

Adjust Limits

Adjust the Upper Limit

Steps to set the highest position for the shade.

Adjust the Lower Limit

Steps to set the lowest position for the shade.

This document describes the Bliss Automation Surface Mounted Wall Switch, a device designed for controlling various types of motorized window coverings.

Function Description:

The Bliss Automation Surface Mounted Wall Switch is a control unit for motorized window coverings, including horizontal blinds (tilt motor), roller/sheer dual/woven motors, and honeycomb cellular motors. It allows users to control the movement (up, down, stop), set upper and lower limits, define favorite positions, and adjust motor speed. The device features a clear LCD display that shows the current channel and other relevant information. It operates bi-directionally, allowing for communication between the wall switch and the motor.

Important Technical Specifications:

Voltage: 3V (CR2430)
Radio Frequency: 433.92 MHz Bi-directional
Transmitting Power: 10 milliwatt
Operating Temperature: 14°F to 122°F (-10°C to 50°C)
RF Modulation: FSK
Lock Function: Yes
IP Rating: IP20
Transmission Distance: Up to 200m (outdoor)

Usage Features:

The wall switch offers a comprehensive set of features for controlling motorized shades:

Channel Selection: Users can select individual channels (1-5) or a group channel (0) to control multiple motors simultaneously. This is done by pressing the "P1" button to cycle through channels.
Pairing: To pair the wall switch with a motor, press and hold the "P1" button for 2 seconds, then press and hold "Stop" for 2 seconds. The motor will jog and beep to confirm pairing.
Setting Upper/Lower Limits:
- Upper Limit: Press and hold "Up" for 2 seconds, then press "Up" and "Stop" for 2 seconds. The motor will jog to confirm.
- Lower Limit: Press and hold "Down" for 2 seconds, then press "Down" and "Stop" for 2 seconds. The motor will jog to confirm.
- Adjusting Limits: For fine-tuning, press and hold "Up" or "Down" for 5 seconds, then use "Up" or "Down" to adjust, and "Up" or "Down" + "Stop" for 2 seconds to save.
Setting Favorite Position: Users can set a favorite intermediate position. Move the shade to the desired position, then press "P2" (on the back of the switch), "Stop", and "Stop" again. The motor will jog to confirm. To send the shade to the favorite position, press "P2" on the front of the switch.
Adding/Removing Remotes: An existing remote can be added or removed by pressing "P2" on the existing remote, then "P2" on the new remote.
Speed Regulation: Motor speed can be increased by pressing "P2" then "Up" then "Up". Speed can be decreased by pressing "P2" then "Down" then "Down".
Roller Mode and Sheer Mode: The wall switch supports different modes for roller/sheer shades.
- Roller Mode: Press and hold "Up" and "Down" for 5 seconds, then "Stop" to switch to roller mode.
- Sheer Mode: Press and hold "Up" and "Down" for 5 seconds, then "Stop" to switch to sheer mode.
Disable Limit Setting (Advanced Feature): This feature prevents accidental changes to the motor limits. To activate, press and hold "Stop" for more than 15 seconds until "L" appears on the display, then press a "P2" button on the back of the wall switch. To re-enable, repeat the process until "U" appears. This feature is recommended for use after all shade programming is complete.

Maintenance Features:

Battery Replacement: The wall switch uses a CR2430 battery. To replace, unscrew the cover, install the new battery with the positive (+) side facing up, and reassemble.
Troubleshooting: The manual provides solutions for common issues:
- Motor no response: Check motor battery, solar panel connection, wall switch battery, radio interference, receiver distance, power supply, and wiring.
- Motor beeps 10 times: Indicates low battery voltage or solar panel issue; recharge with AC adapter or check solar PV panel connection.
- Cannot program a single motor (multiple motors respond): Ensure a dedicated channel is reserved for programming. For multi-motor projects, use an extra 15-channel remote for individual control. To work on a single motor, place other motors into sleep mode by pressing the motor's "P1" button for about 6 seconds until it jogs twice and beeps twice.

Safety Instructions:

Avoid exposing the motor to humidity, dampness, or extreme temperatures.
Do not drill into the motor or cut the antenna.
Keep the antenna clear from metal objects.
Prevent children from playing with the device.
Do not use if the power cable or connector is damaged.
Ensure power cables and antennas are clear and protected from moving parts.
Route cables through walls properly isolated.
Mount the motor in a horizontal position only.
Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
Recycle batteries and damaged electrical products appropriately.

The device complies with U.S. Radio Frequency FCC Compliance and ISED RSS Warning, ensuring it meets regulatory standards for radio communication.